Answered: A closed cylindrical container of…

Name: A closed cylindrical container of length 0.6 m and diameter 0.3 m is
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A closed cylindrical container of length 0.6 m and diameter 0.3 m is full of oil ofsg = 0.85. It is rotated on its vertical axis at 250 RPM. Determine the force exertedon the bottom plate (N).

Engineering

Mechanical Engineering

A closed cylindrical container of length 0.6 m and diameter 0.3 m is full of oil of sg = 0.85. It is rotated on its vertical axis at 250 RPM. Determine the force exerted on the bottom plate (N).

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.90P: The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of...

See similar textbooks

Related questions

Q: Two spheres, each 1.2 m in diameter, weigh 4 kN and 12 kN, respectively. They are connected with a…

A: D=1.2m r=0.6m

Q: A flotation buoy has mass 806 kg, volume 1.43 m, and is attached to the sea floor by a cable in such…

A: Given Mass of buoy, m = 806 kg Volume of buoy, V = 1.43 m3 Density of sea water = 1025 kg/m3…

Q: 1) The centroid of the submerged plane surface and the center of pressure are at the same location.…

A: 1. The centroid of the submerged plane surface is located above the center of pressure. The center…

Q: The uniform rod in Fig. is hinged at point B on thewaterline and is in static equilibrium as shown…

A: Given Data: Mass of lead is m = 2 kg. Specific gravity of lead is SGl=11.4. The length of rod is l…

Q: Problem 2: Calculate the total force on the bottom of the closed tank shown in the figure below if…

Q: A dam 30.5m long retains 8 m of fresh water and is inclined at an angle of 60 degrees. Calculate the…

A: Write the expression to obtain the length.

Q: A concrete block is attached to the gate as shown. If the water level is 1.3 m from the bottom of…

A: Write the given data. H=2 mGs=2.4

Q: As shown in the illustration, a 6-m-wide, 15-m-long barge is filled with rocks and floats in water.…

Q: The gate shown is 3.0 m wide (into the page), hinges around the bottom point, and for the purposes…

A: Force acting on the plate due to weight Fw= 2500 * 9.81 = 24525N Sin60 = d/OA OA= d/sin 60 = 2d/ √3…

Topic Video

Question

A closed cylindrical container of length 0.6 m and diameter 0.3 m is full of oil of
sg = 0.85. It is rotated on its vertical axis at 250 RPM. Determine the force exerted
on the bottom plate (N).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
The 80-kg crate has its center of gravity at G. Determine the smallest force P that will initiate motion if =35.
Each of the three gates has a constant width 1: (perpendicular to the paper). Calculate the force P required to maintain each gate in the position shown. Express your answers in terms of b, c, h, and (the weight density of the fluid).
Determine the horizontal force P that would keep the uniform 12-kg rectangular plate in the position shown.
The tongs shown are designed for lifting blocks of ice. If the weight of the ice block is W, find the horizontal force between the tongs and the ice block at C and D. Neglect the weights of the tongs.
The plane region A is submerged in a ï¬‚uid of weight density . The resultant force of the ï¬‚uid pressure on the region is R acting at the point C (called the pressure center) located at the distance h below the surface of the ï¬‚uid. Show that R=Qa and h=Ia/Qa, where Qa and Ia are the first and second moments of A about the axis a-a.
The automobile, with center of gravity at G, is parked on an 18 slope with its brakes off. Determine the height h of the smallest curb that will prevent the automobile from rolling down the plane.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking brake engaged, which locks the rear wheels. Find (a) the normal forces (perpendicular to the incline) acting under the front and rear pairs of wheels; and (b) the friction force (parallel to the incline) under the rear pair of wheels.
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.