A circular, unfinished concrete drainpipe is laid on a slopeof 0.0025 and is planned to carry from 50 to 300 ft3/s ofrunoff water. Design constraints are that (1) the waterdepth should be no more than three-fourths of the diameterand (2) the flow should always be subcritical. What isthe appropriate pipe diameter to satisfy these requirements?If no commercial pipe is exactly this calculated size, should you buy the next smallest or the next largestpipe?

Q: A horizontal pipe, originally smooth but due to constant use, was found to be scaling through…

A:

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data  Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: 0.60 m lighest water level Lowest water level 21.0 m 1.5 m 672.00 m E Dacil + Water will be…

A: Q=3790  LminQ=3790×10-360Q=.0631 m3secVs=1.5 msec,vb=3…

Q: Select the proper-sized steel tube for a flowrate of 25 gpm and an operating pressure of 1,000 psi.…

A: Basically, the flow rate is the speed at which fluid moves in a pipe, and the flow can be described…

Q: The total length of pipe in the three inch branch is 20 ft, and the length of pipe in the one inch…

A: Given:Total length of the 3" branch pipe, LA=20 ftTotal length of 1" branch pipe, LB=6 ftSpecific…

Q: There are three pipes and each has different friction or roughness factors below

A:

Q: Determine the discharge through three new cast-iron pipe connected in series, having diameters of…

A: To find : The discharge through three new cast-iron pipe connected in series. Given data : The…

Q: Problem 3: A turbulent flow in a pipe has a Reynolds number of 200,000. The pipe diameter is 125 mm,…

A: Given data:Diameter of pipe D = 125 mmReynold’s nuvmber Re = 200,000(a); The relative roughness of…

Q: Calculate the flow through a three-new steel pipes connected in series having diameters of 6 in., 8…

A: Given data: The diameter of pipe 1, d1 = 6 in. The diameter of pipe 2, d2 = 8 in. The diameter of…

Q: Given a frictionless flow of water at 125.6 ft^s in a long, horizontal, conical pipe, of diameter 2…

A:

Q: Water flows at a rate of 2.4f * t ^ 3 / s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Given;

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

A:

Q: A drainage pipe runs on a slope of 1 in 200. The pipe diameter is 500 mm with a 1 mm surface…

A: To find: The discharge when the pipe is half full. Given :  The slope of pipe is s=1200. The…

Q: water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir…

A: RESERVOIR A repository  is most generally an augmented regular or fake lake made utilizing a dam to…

Q: CHOOSE THE CORRECT ANSWER! Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in…

A: To find: The flow in pipe 3. Given: The diameter of the pipes are d1=400 mm1 m1000 mm=0.4 m, d2=350…

Q: 15 m. Determine the rate of flow of water through the pipes pipe of length 1700 m and f= .005, which…

A:

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

A:

Q: What is the entrance length in a 4-cm-diameter pipe if 0.5*10^ -4 m^ 3 / s water is flowing

A:

Q: Write legibly 5. A series galvanized iron pipes (C = 120) consisting of 20 in. diameter of length…

A: Given Data→convert values from inch to feet1 feet = 12 inchD1=20 in =1.667 feetD2=16…

Q: write legibly  Complex Pipeline System_Series Pipes 1. Three new cast-iron pipes were connected in…

A: given: pipe 1 diameter=12in pipe 1 length =1200ft pipe 2 diameter=24in pipe 2 length=2000ft pipe 3…

Q: diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water…

A:

Q: What is the velocity of flow for circular pipe flowing full having a diameter of 250 mm if the…

A: The diameter of the puipe, (d)=250 mm.The length of the pipe, (L)=75 m.The head loss due to…

Q: the following with (True) or (False): 1- The head loss in box culverts varied linearly with the…

A: Given:  Statements are given and we have to find which of them are true and which are false. 1- The…

Q: the hydraulic radius of a pipe with a diameter of 12mm is

A: Pipe diameter, d=12 mm

Q: Figure 5.10 shows the flow net for seepage of water around a single row of sheet piles driven into a…

A:

Q: Series pipe ABCD consists of 10,000 ft of 20′′, 8000 ft of 16′′, and L ft of 12′′ (C = 120). What…

A: Given: The length of pipe AB, L1 = 10,000 ft The diameter of pipe AB, D1 =20 in = 1.666 ft The…

Q: Specifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe…

A: 1. a. 0.0146 cubm/sb. 0.0012 cubm/s2. 6.67 m3. R = 26806Explanation:Since the pipe having Heat…

Q: 1.1 Pelton with a relative density of 0,78 flows upwards in a vertical venture-meter having a…

A:

Q: The following picture represents a network of interconnected pipelines. The arrows rej measured by…

A: Linear equation are as follows,   At C : Entering amount = 30, Exiting amount = X1 and X2As,…

Q: Three pipes of diameters 300 mm, 200 mm and 300 mm and lengths 450 m, 255 m and 315 m respectively…

A:

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A: Write the given data. Q=400 gal/min

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

A: Given data as per the question Length of straight duct upstream to branch = 4m

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.