A circular plate of diameter 4 metres has a circular hole of 1 metre diameter with its centre 1 metre above the centre of the plate as shown in Fig. 35.17. Mm- 1 m 4 m Fig. 35.17. The plate is immersed in water at an angle of 30° to the horizontal and with its top edge 2 metres below the free surface. Find (i) the total pressure on the plate, and (ii) the depth of centre of pressure.

A circular plate of diameter 4 metres has a circular hole of 1 metre diameter with its centre 1 metre above the centre of the plate as shown in Fig. 35.17. Mm- 1 m 4 m Fig. 35.17. The plate is immersed in water at an angle of 30° to the horizontal and with its top edge 2 metres below the free surface. Find (i) the total pressure on the plate, and (ii) the depth of centre of pressure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A sharp-edged orifice , 100 mm in diameter, in the vertical wall of the tank, discharges under a constant head of 1.20 meters. The volume of water discharge in 120 seconds weighs 28.20 kN. At a point 0.783 meters below the center of the orifice, the center of the jet is 1.915 meters horizontally from the vena contracta. Compute the coefficient of contraction O a. 0.64 оБ. 0.68 О с. 0.92 O d. 0.97 О е. 0.6
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. 1 m Liquid (s.g. = 0.88) 4 m B 3.8 m 1 m Fx=123.148 kN and Fy=22.078 kN O Fx=146.005 kN and Fy=28.125 kN O Fx=226.352 kN and Fy=48.953 kN O Fx=249.813 kN and Fy=55.512 kN O Fx=273.251 kN and Fy=59.802 kN O Fx=203.049 kN and Fy=40.981 kN O Fx=298.077 kN and Fy=64.148 kN O Fx=182.117 kN and Fy=36.173 kN Fx=318.195 kN and Fy=68.970 kN O Fx=158.078 kN and Fy=31.450 kN O +
SITUATION. A closed cylindrical tank with 0.60 m diameter and 1.0 m height is fully-filled with water. The tank is rotated at 200 rpm. What is the pressure (kPa) at the circumference of the top base? O 34.74 O 44.55 29.55 O 19.74
n the crest gate on a dam shown in the figure, surface AB forms the arc of a circle of 6 m radius subtending 60° at the hinge. The gate is 8 m long with water surface at B. Compute the vertical component of the total pressure on AB. 6 m hinge 6 m' Unit weight of the liquid (y) Area of the liquid above the crest (A) Given length of the gate Vertical Hydrostatic Force (Fv) m kN m kN ***answer Hydrostatic Force Fv on the box below: Answer: 1059.438 The correct answer is: 355.75
answer it don't need to explain just give the solution
2021-2... ents on A gate 1.60 m wide and 2 m high has water on one side and is inclined 45° with the horizontal. Water is 1.50 m above the top of the gate. Compute the distance of the center of pressure from the centroid of the gate. 1.50 m O 0.1068 m O 0.0871 m O 0.1381 m O 0.0943 m 2.00 m
Fluid 5