A circular metal column is to support load of 500 Tonne and it must not compress more than 0.1 mm. The modulus of elasticity is 210 GPa. The column is 2 m long. Determine cross sectional area and the diameter.

Q: Problem I. With the ongoing extension of Manila Skyway, a series of 250 mm diameter circular poles…

A:

Q: Find the young modulus of the rod of diameter 50 mm and of length 400 mm which is subjected to…

A: Given data:

Q: fowe for the reactlon forces if a 40-kN force k appied connection. on the Ateel rod, near andd fow…

A:

Q: A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight…

A: The cross sectional area of wire is The modulus of elasticity is The yield strength is The…

Q: e sheave diameter

A: Here We need to find Sheave diameter.

Q: The rigid bar AOB is pinned at O and connected to aluminum and steel rods. If the bar is horizontal…

A:

Q: The hanger assembly shown is used to suspend equipment from the ceiling. The length of rod AB is LAB…

A:

Q: Find the greatest weight that can be applied without the front wheels lifting off the ground. The…

A:

Q: 10.14. If P = 1000 Kg find the diameter of the elements subjected to compression to avoid buckling.…

A:

Q: 2. Assume that axial deformation of Member EF is caused mainly by its reaction to external forces on…

A:

Q: round bar of length L. modulus of elasticity E, and weight density tapers uniformly from a diameter…

A: Given:Length of round bar=L,Modulus of elasticity= E,Weight density=γ,Diameter at one end=3DDiameter…

Q: Consider a car of mass 1200 kg with a ground clear- ance of 390 mm supported by four springs of…

A:

Q: Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft…

A: To find: The Euler Buckling load. Given: The length of the column, L = 14.63 m. Young's modulus, E =…

Q: Calculate BC, HC and HG Rod forces in the lattice system?

A:

Q: Compute the internal diameter of the 10 m length hollow cast iron column. If the external diameter…

A:

Q: 2.5 m The jib crane is pin connected at ( A ) and supported by a smooth collar at ( B ). determine…

A:

Q: 4. The three bars are made of steel and form a pin-connected truss. Each bar has a cross sectional…

A: Given: A=3 in2Est=29×106psiT0=50 FTf=110 Fα=6.6×10-6ft/ftF

Q: E 100 175 400 LBE C D 150% 400 E 175 41⁰ 200 B 900 150 G H 930 800 150 200 Dimensions in millimeters…

A:

Q: 03: For the cyclic stress shown in the figure (aside) calculate: 1. The mean stress 2. The range of…

A:

Q: A cable & boom shown, support a load of 600lb. Determine the Tensile Force in the cable and the…

A: Given:-  Load = 600 lb To Find:-  Tensile Force in the cable and the compressive force in the boom

Q: Please solve in Handwritten format with free body diagram. Don't use chatgpt.

A: Step 1:

Q: Two aluminum rods AB and BC hinged to rigid supports, are pinned together at B to carry a vertical…

A: Given data as per the question P =3000 lb cross-section area =0.5 in2 E=10×106 psi Calculations…

Q: 600 N 0.4 m 04 m 03 m- -0.3 m03 m03 m- The frame shown is supported by fixed support at E and smooth…

A:

Q: 9. The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a…

A: First we need to calculate load on the string.

Q: A solid aluminum shaft of 112 mm diameter fits concentrically in a hollow steel tube. Determine the…

A: To find: The minimum internal diameter in mm of the steel tube. Given: The diameter of the shaft is…

Q: 1. The timber member has a cross-sectional area of 1700 mm2 and its modulus of elasticity is 12 GPa.…

A:

Q: Find the Young’s modulus (Y) of the steel rod of 1 m long and a cross sectional area of 0.05 cm2,…

A: Given data:- The length of the rod                       The cross-sectional area…

Q: A cubic block with an edge of 0.2 m and a weight of 98 N lies on another cubic block of the same…

A:

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A:

Q: The sphere has a mass of m-6kg, the spring has an elongation of 9.2cm and the angles of the rope…

A: According to the data  m=6kg mg=6x9.81=58.86 N x=9.2cm=0.092m we need to find Stiffness constant

Q: Question 3: Given properties of the system are q1=15 kN/m, q=20KN/m, hj=30m, Lı=30m and L=15m. If…

A:

Q: The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ionger than…

A:

Q: Determine the nominal compressive strength (P.) of a W12x96 column with no bracing and an unbraced…

A:

Q: A column with rectangular cross section of breadth = 9mm and depth = 4mm, has its both ends are…

A:

Q: The assembly consists of three disks A, B, and C that are used to support the load of P. The load P…

A: Given data

Q: A central horizontal section of a hook is a symmetrical trapezium of inner width =67.5mm and of…

A: Given:Inner width,bi=67.5 mmOuter width,bo=22.5 mmP=37.5 KNInner radius,Ri=52.5 mmh=90 mmOuter…

Q: A straight girder of uniform section and length L rests on supports at the ends, and is propped up…

A:

Q: d/2 Determine the support reaction at the rigid supports A and C as a 3P + function of P. Member AB…

A:

Q: 1. A homogeneous 800 kg bar AB is supported at either end by a cable. Calculate the smallest area of…

A: To find: The smallest area of each cable. Given: The mass of bar AB is m=800 kg. The stress is not…

Q: 7. Find the Su of a 2 cm diameter hollow cylinder that has a wall thickness of 1 mm and collapses…

A:

Q: GAP BAR A BAR A BAR B

A: Stress produced in the material due to changes in temperature is known as thermal stress. Conditions…