A circular metal column is to support a load of 500 Tonne and it must not compress more than 0.1 mm. The modulus of elasticity is 210 GPa. the column is 2 m long. Calculate the cross sectional area and the diameter. (0.467 m² and 0.771 m) Note 1 Tonne is 1000 kg.

A circular metal column is to support a load of 500 Tonne and it must not compress more than 0.1 mm. The modulus of elasticity is 210 GPa. the column is 2 m long. Calculate the cross sectional area and the diameter. (0.467 m² and 0.771 m) Note 1 Tonne is 1000 kg.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 30mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is…

A: Do=800.5mm Di=800mm E=200GPa

Q: Figure P-251 A L= 5 ft L= 3 ft 2 ft 6000 4 ft 4 ft

Q: A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and…

A: The load is P=10 kN. The length is l=3 m. The cross-sectional area is A=1000 mm2. The modulus of…

Q: Suppose that P = 450 lb in (Figure 1). Figure P 600 lb E -3 ft D B 30° -3 ft- Determine the force…

Q: Q.10 The equivalent stiffness for the system shown below is units. If flexural rigidity of beam is…

A: We have to determine equivalent stiffness. Given, Length of beam = 2m Flexural rigidity is unity.…

Q: Calculate the nominal moment strength of a reinforced concrete beam 230 mm x 460 mm if at failure…

A: Given,Cross section of beam , B×D=230×460 mm2compression strain, εc= 0.003tensile steel strain, εs=…

Q: b= 10.1 in 1= 0.855 in The variables a and b are defined by the last two digits of your Z-number.…

A: Design of Tension member as per IS: 800-2007 Given: A992 steel a= 4; b = 1 so, L = (10+4) =14 in Ag…

Q: Q.17 The equivalent stiffness for the system shown below is units. If flexural rigidity of beam is…

A: Now, equivalent stiffness is

Q: Om A 1+(ec/k²)sec[0.5JP/(EA)(L/k)] where ec/k?=the eccentricity ratio and E is the modulus of…

Q: An aluminum rectangular bar has a cross-section of 25 mm x 50 mm and a length of 500 mm. The Modulus…

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

A: Finding out normal stresses at each segment.

Q: Calculate the nominal moment strength of a reinforced concrete beam 270 mm x 490 mm if at failure…

A: Given b = 270 mm, h = 490mm f'c=27MPa fy=420MPa To find The nominal moment strength

Q: 1. The triangular block shown in Fig. P-010 is subjected to the loads P = 1600 lb and F = 600 lb. If…

A: Given data Force F = 600 lb Force P = 1600 lb Side AB = 8 in Side BC = 6 in To resolve Force in…

Q: Q.17 The equivalent stiffness for the system shown below is units. If flexural rigidity of beam is…

A: Follow next step for solution.

Q: Three rods, cach of area 250 mm2. jointly support a 7.5 kN load, as shown in Figure below. Find the…

A: My dear Given data Total hanging load Two types of materials. Area of cross section Youngs modulus…

Q: The 33-mm-diameter A992 steel rod is subjected to the loading shown. Take E= 200 GPa. (Figure 1)…

Q: Find the magnitude P of the largest additional vertical force that can be applied to the bar decimal…

Q: STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal…

Q: As shown, three steel wires, each 26 mm in area, are used to lift a mass M. Their unstretched…

Q: A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper…

Q: 125 25 mm/25 mn 12AN SAN 75 25 mm

Q: DETERMINE THE FORCE (Ib) FOR MEMBER AC GIVEN THE DATA BELOW: F1 = 997 lb F2 = 1,449 lb **Note: for…

Q: Q.17 The equivalent stiffness for the system shown below is units. If flexural rigidity of beam is…

A: Given data , flexural rigidity of beam is unity. Length of beam is 2m And stiffness of spring is 12…

Q: Two rigid bars are connected with a rotationalspring, as shown in the figure. Assumethat the elastic…

A: Given:- L=6fth βR = 75 kip-in./rad To find:- Pcr

Q: 3. A uniform steel bar of length 1.65 m, has a cross sectional area of 17,671 mm? and unit mass 7850…

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

Q: etermine the force in each member of the truss. State e members are in tension or compression. Take…

Q: Help me with Solution, Need fast. Do not waste time. A steel beam is installed in a building when…

Q: A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are…

A: Given:-P=2500 lb Diameter= 3/16 in L=20 feet=240 inches To find:- Stresses in wire Solution:-…

Q: Calculate the nominal moment strength of a reinforced concrete beam 270 mm x 490 mm if at failure…

A: Given Data b = 270 mm, h = 490mm Assuming cover of 40mm d = 490-40 = 50mm…

Q: Suppose that P = 450 lb in (Figure 1). igure P 600 lb E -3 ft D B 30° -3 ft 1 of 1 > Express your…

A: A truss hinged at A and roller supported at C is given.The truss is statically determinate.To…

Q: 342 Strength of Materials 16. A steel post (E = 200 GPa) having thickness t = 3 mm and height L = 2…

Q: 2 The 600 KN load is horizontal when it is first applied to the columns. After some time, the 600 KN…

Q: A high-strength steel bar used in a large crane has diameter d = 2.50 in. (see figure). The steel…

Q: A closed right circular cylinder has radius 2 units and height 17 units A load of an unknown weight…

Q: SITUATION. The figure shows a pellet about to be fired from a sling. The total unstretched length of…

A: What is the force in each leg of the rubber,F=?

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24 kN is applied to the rod as shown. The elastic modulus is E = 2.6 GPa and Poisson's ratio for this material is v=0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. tel Answer: Ad= i Ja ↑ L mm
Please answer it clearly dont waste my question, I will vote it up for your effort and thank you in advance.
SHOW COMPLETE ANSWER AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 4: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of castiron 5 mm thick. Compute the load that will compress the combined bar a total of 1 mm. For steel, E = 200 GPa, and for cast iron, E = 100 GPa.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m
!!!
answer quickly
Fast now
D Question 7 A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and has an elongation of 0.009 in. The initial radius of the material is most nearly? O 0.94 in O 0.10 in O 0.31 in O 2.83 in
* Your answer is incorrect. A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24 kN is applied to the rod as shown. The elastic modulus is E = 2.6 GPa and Poisson's ratio for this material is v= 0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad= i -0.21 L mm
Please answer correctly. Please I need this ASAP. thank you Note: The tolerance is ± 1 in the third significant digit
Please solve it within 30 minutes please i need help formulas are also attached
A 3 m long beam has a 4 kN/m distributed load applied to the cantilever steel beam as shown below. The dimensions for a = 40,b= 40, c = 40, and d = 100. a w kN/m >a d Section a-a (unit in mm) Mc M 1_M FORMULAS: 06 = or == " I S P EI L b C