A circular disk with a radius of 0.38 m is subject to 2 tangentially applied forces. The disc is fixed such that it will rotate about its center. Both forces produce a torque in the same direction. F1 = 3.5 N applied at the outer edge of the disc. F2 = 3.2 N applied at a distance of 0.28 from the center of the disc. What is the net torque on the disc?

Q: A wrench 0.3 meters long lies along the positive y-axis, and grips a bolt at the origin. A force is…

A:

Q: When opening a door, you push on it perpendicularly with a force of 57.5 N at a distance of 0.75 m…

A: Given data:  Force (F) = 57.5 N Distance (r) = 0.75 m Angle (θ) = 90°, Perpendicular Required:…

Q: The body in the figure is pivoted at O, and two forces act on it as shown. If r = 2.03 m, r2 = 3.93…

A:

Q: In the figure, a square piece of wood is pivoted at its center. Each of the forces A, B, C, and D…

A: We note the following lengths

Q: A one-piece cylinder has a core section protruding from the larger drum and is free to rotate around…

A:

Q: A 100 N force exerted at the end of a 0.50 m long torque wrench supplies a torque of 20 N·m. What is…

A:

Q: A uniform door weighs 51.00 N and is 1.100 m wide and 2.400 m high. What is the magnitude of the…

A: Given data: The weight of the door is W=51 N. The height of door is h=2.4 m. The width of the door…

Q: F3 F1 F2

A: Given, Radius, r=0.53m F1=14.7N F2=11.1N F3=11.5N Net torque is given by, τnet=∑r×F

Q: A hamster sits 0.10 m from the center of a lazy Susan of negligible mass. The wheel has an angular…

A: distance, r = 0.1 m , angular velocity, ω = 1 rev/s distance, r' = 0.3 m

Q: The figure below shows forces acting at various points on a metal shaft. The angles ? = 48°, ? =…

A: Given data, Angels, α=48°β=35°γ=21° Length l=3.6 m

Q: A force F =7.2î +2.3k N is applied at the point (3,0,1) m. What is the y component of the torque?

A: To answer the question we will use the formula: Τ→=r→×F→

Q: As shown below, a 25 kg bar that is 1.8 m long is set up to rotate about its center (the yellow…

A:

Q: Sierra holds a box in her hand using her elbow flexor muscles (see picture). Her forearm is at a 35°…

A: Angle of forearm relative to horizontal θ=35o Length of the elbow from box to joint L=0.28 m Weight…

Q: An 8.0-cm radius disk with a rotational inertia of 0.12 kg.m² is free to rotate on a horizontal…

A: 1:1. Relate Torque and Angular Acceleration:• Torque (τ): This is a rotational force that causes an…

Q: How much torque would it take to make the wheel speed up from rest to 1.5 rev/sec in 10 sec? b. Now…

A: The moment of inertia of a rigid body is the sum of the products of the masses of all the particles…

Q: The 20-cm-diameter disk shown can rotate on an axle through its center. What is the net torque about…

A: Let the first force acting on the disk is 30 N. In this case the center of the disk will act as a…

Q: Two objects are connected by a 1.0-m-long massless bar. One object has twice the mass of the other.…

A:

Q: If you hold your arm outstretched with your palm upward, the force to keep your arm from falling…

A:

Q: the torque be in

A: We are given a wheel. It is speeding up by rotating clockwise. We have to find in what direction…

Q: A ten pound car wheel has a moment of inertia of 0.36 kg m². While rotating at a constant speed the…

A:

Q: If you hold your arm outstretched with your palm upward, the force to keep your arm from falling…

A: The torque is given the formula:Given:Mass of the arm () = 4.25 kgAcceleration due to gravity () =…

Q: A large wind turbine has I= .45 mr². The mass of the turning hub and blades is 3800 kg with a radius…

A:

Q: A disk of mass M = 2.0 kg and radius R = 0.25 m is free to rotate about its center. Two forces, F1 =…

A: The mass of the disk is m = 2 kg. The radius of the disk is r = 0.25 m. The applied force F1 = 1.0…

Q: 8. A 3 kg uniform disk has a radius of 2 m. An external torque of 10 N-m is applied to the outside…

A: Since you have posted a question with a multiple sub parts, we will solve first three sub - parts…

Q: We revisit the ball (mass of 100 g) that was attached at the end of the string. The distance between…

A:

Q: A 400 kg solid metal disk (with uniform density) has several forces applied to it, as shown. If the…

A: Net torque acting on the solid metal disk is τnet=r1F1+r2F2-r3F3=0.5 m×18 N+1.0 m×15 N-0.5 m×20 N=14…

Q: A force given by F1 = (100N, -20 deg) is applied to the right end of a 6 meter long rod aligned…

A: Given:  F1 = 100 N, -20 degree at 6 m  F2 = 200 N , 120 degree at 1 m  F3 = 220 N , 110 degree at 3…

Q: A thin rod (seesaw) has length L m and mass M kg. It is resting at an angle of 30° with respect to…

A:

Q: Which of the following statements are true?       The magnitude of torque is the same for any axis…

A:

Q: In the figure, block 1 has mass m1 = 0.460 kg, block 2 has mass m2 = 0.500 kg, and the pulley, which…

A:

Q: A wrench 60 cm long is attached to a nut and bolt. You exert a 40 N force on the wrench. What is the…

A:

Q: 2 m P 45° 60° 6 m F

A: F1 = 20 N F2 = 25 N θ1 = 45oθ2 = 60o

Q: A student holds a stick as in the diagram in the position shown where a = 23.0°. The mass of the…

A: Given value--- mass = 3.70 kg. length = 4.4 m. angle = 23 degree. We have to find--- torque?

Q: enti

A: GivenF=5 Nr=36 cm=0.36 mWheel starting from restωo=0θ=10 rev=10×2π radt=4 s