A circular bar of radius R = 200 mm is replaced by a hollow bar of inner and outer radii Ri and Ro, respectively, with Ro/R; = 2. If the two bars are made of the same material and can carry the same maximum torque, determine (1) the outer radius of the hollow bar, Ro, and (2) the mass ratio for the hollow and solid bars.

A circular bar of radius R = 200 mm is replaced by a hollow bar of inner and outer radii Ri and Ro, respectively, with Ro/R; = 2. If the two bars are made of the same material and can carry the same maximum torque, determine (1) the outer radius of the hollow bar, Ro, and (2) the mass ratio for the hollow and solid bars.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft having length equal to 10 m and diameter equal to (50+ 16) mm is simply supported at both ends. The shaft carries four masses (150 + 16) kg, (200 + 16) kg, (250 + 16) kg and (300 + 16) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A shaft having length equal to 10 m and diameter equal to (50+ 01) mm is simply supported at both ends. The shaft carries four masses (150 + 01) kg, (200 + 01) kg, (250 + 01) kg and (300 + 01) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
2. The tapered cylindrical bar in Fig. 2 is subjected to opposing torques T on its free ends. For the tapered section only, the angle of twist 0 can be expressed as: 32 TI(d? + d,d2 + dž) Gd d? 37n (a) Derive an expression for the effective spring constant keff for the entire bar, treating each segment as a torsional spring in series. Fig. 2 (b) For the bar shown, let; I, = 12 = 12 in., 1= 24 in., d1= 0.25 in., d2= 1 in., T = 1000 lbf-in., and G = 13.5 x 103 kpsi. Calculate the angle twist 0 for the entire bar using the expression for kef determined in (a). Verify that this value is the sum the angles of twist for each individual %3D %3D segment.
A brake test is carried out with a balance and a direct current motor. The purpose of this experiment is to calculate the torque on the motor shaft. The following values were obtained in the experiment. U=220 volts., I=107 amps, n = 1200 rpm. The length from the axis of the motor shaft to the point where the brake lever presses on the scale is L=80 cm. and the weight read on the balance G = 20 Kg. is Accordingly, calculate the following values: a) the shaft power taken from the shaft of the motor, b) the electrical power drawn by the motor from the mains c) motor total losses and motor efficiency Calculate
Problem 3.55 not 3.54, problem 3.55
7
The mechanism of four rods (Rocker Crank) as shown in the picture below is O₂A = 15 cm long, AB = 40 cm, BD = 10 cm, O2O4 = 45 cm, and O4B = 30 cm. Bar 4 receives a force Q of 4000 N. Determine the magnitude and direction of the torque in rod 2.
finished in an analytical way
A maximum torque of 6.75 kNm can be supplied to the constant diameter steel (G= 80 GPa) line shaft by a motor as shown in Figure Q2. At the current normal operation condition, three machines are driven by gear B, C and D on the shaft and they require torques of 3.x kNm, 1.5y kNm and 1.0z kNm, respectively. Parameter x, y, and z are given by: Q2 X=0 Y=0 Z=2 Considering the maximum torque can be supplied by motor, determine the minimum diameter required if the maximum shearing stress in the shaft is limited to 100 MPa. Round your answer to the nearest whole number. (a) -Bearing D Figure Q2
5. The presence of a net external torque will still lead to a conservation of angular moment of a rotating body True False
A disk and a ring both homogeneous with masses M1=0.94 kg and M2=M1/6 and radii R1=0.36 m and R2=R1/2, respectively, are coupled by an ideal C strap, as shown in the figure below . At a given moment, a work of modulus W=35 J is performed on the system that, starting from rest, makes the disk and the ring rotate around their symmetry axes. In view of this, answer: what is the value of the linear velocity v at the edge of the disk? Consider that the strap does not slide over the edge of objects. Choose one: Escolha uma: a. 14,80 m/s b. 12,68 m/s c. 10,57 m/s d. None of the other alternatives e. 19,02 m/s f. 16,91 m/s g. 8,46 m/s h. 6,34 m/s
i need the answer quickly