A circuit consisting of a filter and an op-amp is shown in the figure below (fig. 7). If R1 = 5 ohms, C1 = 4 farads and if the frequency of the input voltage is 1 rads/sec, calculate the voltage gain of the circuit in dBs (decibels). Insert only the numerical part of your answer without the units. R1 Vin Fig. 7 C1 Vout •T-

A circuit consisting of a filter and an op-amp is shown in the figure below (fig. 7). If R1 = 5 ohms, C1 = 4 farads and if the frequency of the input voltage is 1 rads/sec, calculate the voltage gain of the circuit in dBs (decibels). Insert only the numerical part of your answer without the units. R1 Vin Fig. 7 C1 Vout •T-

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Assume that the JFET with the transconductance curve shown in the figure for Problem 3 is connected in the circuit shown in the following figure. a. What is VS? What is ID? What is VDS? b. c. WI RG 1.0 ΜΩ +VDD +15 V O RD 33 ΚΩ Rs 10 k figure 3 Vas (V)- -6 -5 -4 -3 -2 -1 ID (MA) 7.0 6.0 5.0 4.0 3.0 0 2.0 1.0
- V2 15Vdo 3 U1A R1 2 1k V- LM324 1k V3 15Vde | VOFF = 0 VAMPL = 1 FREQ = 2k AC = 0 0. R2 Figure 4. Operational amplifier circuit. What frequency does the output voltage (across R3) have? What is the amplitude of the output voltage? From the output waveform and the input waveform, determine the gain of the op-amp circuit. Does this match with what you predicted? How could you change this circuit so that the output voltage would be nearly the same as the input voltage? What purpose would that serve? Can you modify the existing circuit and verify this experimentally? What is the phase difference between the output and input voltage? Derive the transfer function for the output-input relationship for the operational amplifier. How would the gain and the output change if a capacitor were in the feedback path instead of a resistor? (Examine the circuit using phasors and impedance and circuit analysis techniques). -w-
Question 1: a) Sketch Vo versus time for the circuit shown with the input given. b) Determine DC output voltage without a capacitor. c) If a capacitor of 10 uF is placed in parallel with RL, sketch the vo versus time. d) find the DC output voltage. Given R1 = R2 = RL = 2.2 k2. Vi +40 D1. D2 10 ms R = 2.2 k2 ww R%3D 1GF R = -40 2.2 k2 2.2 k2
85!ו nl- 20:01 3 docs.google.com/forms/d/e * اسم الطالب Q/ Compute the Voltage gain (GV) theoretically and then the output voltage (Vou) for the inverting OP amp circuit shown in figure and prove RLVin that the Vout = - Rin 20 k2 +Vcc 10 k2 Vout = ? 12 v -Vee our answer
V₁ + R Answer: Answer: + Consider the network above with V₁ = 9V. V₂ = 11V, and R = 1.2k. Treat the op-amp as real, with ß = 2 × 10³, R₂ = 3MQ, and R₁. = 750. a. What is the voltage v across the input terminals? + Answer: 3R b. What is the current in through the input terminals? + Vout Answer: c. What is the "ideal" output voltage (treating the op-amp as ideal)? d. What is the difference between the ideal and real output voltage? (Compute Vreal - Videal.) (For (a), enter 8 digits of precision. For the rest, enter 4 digits.)
What is the amplitudes and polarity of trigger puise and Sketch the output Tor 3 trigger puises. R1 10 R2 +10 V Vin Vout Vyef -10 V -10- Fig. 1 2. 3. t(ms) IN "A
The circuit shown below includes an ideal op aıp. What is the output voltage, Vo, of the circuit? 12 V 30 10 V 70.2 O O volts 30.5 volts O 58.7 volts O 85.3 volts
ı just need fınal aswer If VGSQ = 7 V, C1 = 32 nF and C2 = 150 nF in the circuit in the figure, what is the low cut-off frequency of the system? NOTE: rd will be taken into account in calculations. a. 68,99 Hz b. 110,38 Hz c. 13,80 Hz d. 27,60 Hz e. 41,39 Hz f. 82,79 Hz g. 96,58 Hz h. 137,98 Hz
V₁ V₂ Answer: Answer: 2R ww 3R Consider the network above with V₁ = 7V, V₂ = 8V, and R = 4kQ. Treat the op-amp as real, with ß = 2 × 10³, R₂ = 1.2MQ, and Ry = 902. a. What is the voltage vy across the input terminals? Answer: Hll! b. What is the current i, through the input terminals? ww R Answer: c. What is the "ideal" output voltage (treating the op-amp as ideal)? + Vout d. What is the difference between the ideal and real output voltage? (Compute Vreal - Videal.) (Enter 8 digits of precision for part (a). Enter 4 digits for the rest.)
The datasheet of an Op-Amp gives AoL = 150,000 and CMRR = 85 dB. What is the common-mode voltage gain? Show the details of your work.
The components in the circuit shown below are ideal. If the op-amp is in positive feedback and the input voltage V, is a sine wave of amplitude 1 V, the output voltage V, is 1 kΩ ww +5 V 1 V 1 k2 V,o WW -1 V -5 V (a) a square wave of 5 V amplitude (b) an inverted sine wave of 1 V amplitude (c) a non-inverted sine wave of 2 V amplitude (d) a constant of either +5 or -5 V
Q3) for the RC oscillator circuit shown with = 1 nF and R =1 KQ answer the following: 1. Find the value of Rf and Ri to start oscillation 2. What is the phase shift of each RC-section if there is 6 RC-sections 3. For the same frequency of oscillation design another RC oscillator circuit using non-inverting configuration of Op-amp R; Ор-amp