A channel shape is used to support the loads shown on the beam. The dimensions of the shape are also shown. Assume LAB-3 ft, Lec-9 ft, P=2050 lb, w-1200 lb/ft, b=12 in, d-5 in, t-0.875 in. Consider the entire 12-ft length of the beam and determine Determine the maximum compression bending stress at any location along the beam Answer in ksi rounded-off to 2 decimal places. Report the answers here using the correct signs. LAB

A channel shape is used to support the loads shown on the beam. The dimensions of the shape are also shown. Assume LAB-3 ft, Lec-9 ft, P=2050 lb, w-1200 lb/ft, b=12 in, d-5 in, t-0.875 in. Consider the entire 12-ft length of the beam and determine Determine the maximum compression bending stress at any location along the beam Answer in ksi rounded-off to 2 decimal places. Report the answers here using the correct signs. LAB

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2) Find the shear center of the section below and calculate the maximum shear stress that occurs in the section as a result of the loading shown in the figure. The section thickness is uniform everywhere and is 10 mm. Note: G.M is the geometry center of the section, the shear force of 40 kN acts from the geometry center of the section. You can look at your lecture notes for the coefficients you will need. 160 mm V-40 kN t LG.M 100 mm
02: The rigid platform has negligible mass and rests on two steel bars, each 250.00 mm long. The center bar is aluminum and 249.90 mm long. Compute the stress in the aluminum bar after the center load P= 400 kN has been applied. For each steel bar, the area is 1200 mm2 and E= 200 GPa. For the aluminum bar, the area is 2400 mm2 and E 70 GPa Rigid platform Steel Ahmum Steel
This problem is called design of beam for questions 8A, 8B, and 8C with the section shown in figure 08. A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. 8A. Determine the maximum value of w without exceeding the permissible flexure stress of 10MPa
A wood beam is strengthened using two steel plates as shown in the figure below. 6 mm O. 150 mm C 6 mm 100 mm- The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 14 kN q = 4.6 kN/m B 3 m +1m Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood 6.52 MPa maximum tensile stress in steel 128.12 V MPa maximum compressive stress in wood 6.52 The response you submitted has the wrong sign. MPa maximum compressive stress in steel 128.12 The response you submitted has the wrong sign. MPa
3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa 4. In question 3, assume that the bar is free to elongate or shorten, calculate the change in the length of the bar if the temperature drops from 20°C to -20°C.
Q2: The simply supported beam shown as Figure 5. below is subjected to Loading as shown on the Figure. Using integration method. Find the maximum Lenght (L) so that the max. deflection is not greater than 30mm for the Beam.. The flexural rigidity (El) of Beam section El = 50*10% KN.m? “4m e | Sm