A certain masonry dam requires 150,000 cu.m. of gravel for its construction. The contractor found 2 possible Sources for the gravel with the followwing data-

Q: For the figure shown, if P = 50 kN and the vertical movement of end C is limited to 4 mm, then the…

A: Option -- 1250 mm2

Q: Construct a truth table for [(M - J) A (J-S)) - (M-S)

A:

Q: The parameter COD is: O a. Usually less in value than the ulitmate BOD b. Usually equal in value to…

A: The parameter COD is: a. Usually less in value than the ulitmate BODb. Usually equal in value to…

Q: - the upper part in fig below is a steel and lower part is a cast iron , the load P shortens the…

A:

Q: for part b, what happened to the t on the cty when integrating, can you please show this work again?

A: Given: u = A(1+bt) , v = cty  Required: To explain the stream line equation done in step 2 by the…

Q: Figure 50 mm 150 mm 150 mm 300 mm 1 of 1 Locate the centroid y of the bea Express your answer to…

A:

Q: COMPLETE THE STATEMENTS BELOW. TYPE YOUR ANSWERS IN THE BOX. Refer to the figure shown. Given a…

A: Given Data Determine  1. In collapse-2, Y1 = ? θ 2. In collapse-2, Y2 = ? θ  3. In collapse-2, Y2…

Q: At a point in a stressed body, the known stresses are o, = 37 MPa (T), oy = 24 MPa (C), o, = 20 MPa…

A:

Q: Find the centroid of channel shown in figure T 100 mm K > K C B F 80 mm -10 mm G H 10 mm A T 50 mm -…

A:

Q: Slope deflection to determine the forces reactions

A: Sign convention : assuming clockwise moments as positive(+) and anti-clockwise moments as…

Q: Solve for: [D"C]E a. b. 5АВ - ЗС 4 1 .?

A:

Q: The railroad I-beam has dimensions as shown below. In reviewing these old designs, you have been…

A:

Q: Plane a-a is called the D.

A:

Q: The degree of homogeneity of the function f(x, y) = (x² - 4y²)-¹/2 O A. 1 OB.-1 O C. -1/2 O D. None…

A:

Q: what is design strength. The material of the steel is SM275 and the size is 22mm. The sectional area…

A: Tensile Strength : Tensile means "competent of being drawn out or stretched." Steel's tensile…

Q: The beam shown requires two plastic hinges for its collapse mechanism. y = 120 W₁ = Mp (40) The…

A: Answer  (1) We know that required number of plastic hinge in a structure for its collapse is given…

Q: Q6• For figure below, caleulate the forces Surfaces on A f B. surface 8 (area = o-1m²) 0.1 air 2 w…

A:

Q: Solve for the centroid of the figure relative to the bottom fiber. You'll be solving only for the y…

A: Unsystematic section is given and it has been asked to determine centroid of y axis. Please refer…

Q: Find the NA here:

A:

Q: Determine the stability and determinacy b b+r = 2j ANAMAN N Classification

A: b + r = 2j ( statically Determinate ) b + r > 2j ( statically Indeterminate ) b + r < 2j (…

Q: 5- What should be the maximum value of cant excess on Broad gauge? a. 65mm b. 75mm c. 92mm d. 100mm…

A:

Q: Identify the purpose of municipalities such as City and Town Governments hiring an engineering firm.…

A: 1) In a municipalities a muncipal engineer is hired to handle small engineering projects and…

Q: * = pw 2 gm/cm3 1 gm/cm³ O 4 gm/cm³ O 3 gm/cm³ ОООС

A: 1 g/cm3

Q: ) Prove that stroctare is salee I Stakicalle dotaminate

A: Since the question number to be solved is not specified, the solution for subpart a is as follows:…

Q: : Prtal methed

A:

Q: The typical units of Cc and Cr are: O Ib/ft? and kPa O Ib/ft and kN/m3 O inches or milimeters O…

A: step 1-

Q: Deter mine the vatation atprint sf the frame shown in figuve. Take E: 20010 mpa 1=30 lo mm4 SEN…

A:

Q: y Ball and sockets 12 D X1 5 X2 E Y1 Z2 z1

A: Step 1

Q: 3. For the composite area shown, determine the following: a. Find the moments of inertia Ix and ly…

A:

Q: The centroid of the T-section shown is 2.5 inches above the base. What should be the value of b to…

A: Given A T section having centroid 2.5 inch above the base.  Required Value of b

Q: Explain the difference between S, and o

A: Difference between sx , and σ :- The distinction between the sigma (σ) and 'sx' as generally…

Q: Explain withe help of Steps Of X to find the value the sesisting 'F" dusing fos un Ais plane be…

A: Dimensional analysis - To develop a functional relationship between the variable.  modal and…

Q: Explain the following terms used in GMS. a. IBOUND b. HANI c. RCH d. SY e. SS

A: IBOUNDHANIRCHSYSS

Q: Determine external as well as total indeterminacy

A: Given data : Number of external support reaction (R)=2+1=3Number of member (m)=15Number of Joint…

Q: 0.5 EI mm S=10 40 EI -5 2 E = 2.1+ 10 N/m² I=70,000 cm4 √ = 10 mm a EJ 2EI b At = 10°c h t = 20%…

A: The given structure is a beam with a span of 2 meters, supported at both ends. The beam has a…

Q: Problem 8: Approximate Analysis for Vertical Loads

A: Approximate analysis for vertical loads typically involves simplifying the structural system to…