A centrifugal pump with radial inlet (alpha4 = 90°) operates with water at a flow of 0.3 m3 /s. The rotor diameter is 250 mm and the blades it is 30 mm wide at the outlet. Assume that the blades are radial at the exit. Determine the theoretical height considering infinite number of blades and power required when the pump runs at 800 rpm.

Q: The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A:

Q: a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating…

A:

Q: A well has ¾ in of sucker rod and 21/2 in tubing with a specific gravity of the produced fluid of…

A:

Q: 1. A pump pumping liquid propellant operates at 10,000 rpm. The volumetric flow rate through the…

A:

Q: A gear pump has gears of 300 mm outside diameter, 150 mm inside diameter and 50 mm width. If the…

A:

Q: A pump is driven at 1800 RPM and delivers 12 GPM at 2000 psi. If the volumetric efficiency is 90%,…

A:

Q: A centrifugal pump delivers 180 liters /s of water and the blade exit angle is 25° from the…

A:

Q: /A Pelton wheel has a tangential velocity of buckets of 15 meters/sec. the water is being supplied…

A: calculated the power produced by the wheel in watts.

Q: Problem 4: Compute the specific speed for a pump operating at 1750 rpm delivering 12 000 gal/min of…

A:

Q: assume a flow of 1.7 m3/hr. the pressure readings are 0.1 bar at the bare pump and 0.3 at the…

A: assume a flow of 1.7 m3/hr. the pressure readings are 0.1 bar at the bare pump and 0.3 at the…

Q: In an external gear pump, if the delivery rate  is 8 cm3/revolution, the prime mover's speed which…

A: Delivery rate = 8 cm3/revolution Speed = 2500 rpm

Q: A centrifugal pump has a rotor of 170mm dia and runs at 1, 450 rpm. It is 15mm deep at the outer…

A: Diameter of rotor = 170mmSpeed N = 1450 rpmdepth at the outer edge = 15mm 30°Vense take 10% of the…

Q: A system requires delivery of water at 40 l/s at a head of 12 ft. An axial pump is available. What…

A: Given that, Flow rate through the pump, Q=40 L/sec,Q=40×2.12 ft3/min  (1 L/s=2.12 ft3/min)Q=84.8…

Q: A centrifugal pump has impeller with dimensions r1 = 78 mm, r2 = 143 mm, b1 = 54 mm, b2 = 26 mm, β1…

A:

Q: e power required to drive t e pump.

A: Need to find the power required to drive the pump.

Q: speed to the water jet speed is?

A: Given; For a pelton wheel with a given water jet velocity the maximumoutput power from the pelton…

Q: A centrifugal pump is designed to operate at 1800 revolutions per minute and with a head of 55…

A:

Q: Please solve it correctly asap !!! A double- suction centrifugal pump delivers 3 m3/s of water at a…

A: find:specific speed of the pump

Q: The pump has an er diameter of 8 cr 1750

A: The outer diameter of the pump is .The inner diameter of the pump is .The width of the blade is .The…

Q: 3/3 Summarize the rotor theory of centrifugal pumps, focusing on the following topics: Influence of…

A: The fundamental equation of turbo pumps, also known as the Euler turbomachine equation, is a…

Q: A nozzle of diameter 20 mm at one end is used to eject water with a 20 m/s of designed velocity.…

A: Given data: The diameter of the nozzle at converged end is d1 = 20 mm. The designed velocity of…

Q: A Pelton wheel has a mean bucket speed of 10 meters per second with a jet of water flowing at a rate…

A:

Q: A centrifugal pump is used to pump water (1000 kg/m³) to a height of 10m, the water splashes down…

A: Given    Density = 1000 kg/m³   Head, h = 10 m Speed, N = 2900 rpm Find   Flow rate

Q: single-stage centrifugal pump has an impeller speed of 1750 rpm. If the flow rate of water is 60…

A:

Q: Determine the mass fow rate of the liquid through the pump?

A: Given data;  Entry of liquid into the pump is axial and exit from the pump is radial with respect to…

Q: A centrifugal pump delivers water at a rate of 0.03 m'/sec to a helght of 18 meters through a pipe…

A: We have given data from the question are, Q=30 L/s=301000 m3/s=0.03 m3/sH=18 m,L=90 m

Q: The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A: Given Data :  Plunger Diameter D = 115mm = 0.115 m Stroke Length L = 230 mm =0.23 m         So, r…

Q: A three stage pump delivers 2.66 m3/s against a head of 200 m with a speed of 2000 rpm. Find the…

A: Given data Discharge = 2.66 m3/s Head = 200 m  Speed = 2000 rpm We have to find specific speed of…

Q: The fluid flow rate was 1 m3 / s and the head was 10 m in the experiment performed at 2000 rpm with…

A:

Q: An idelaized centrifugal pump, data given as follows; Blade outer radius of blade = 30 mm Power = 1…

A:

Q: operates at a speed of 1450 rpm and discharge a efficiency=55%. head of 40m and 1- Calculate the…

A: Given data as per question N=1450 rpmQ=250 m3/hrH=40 mη=55 %

Q: For Questions 3 to 5, consider the following conditions: a centrifugal pump has diameters d1 = 7 in,…

A:

Q: Determine the head developed by a multi-stage pump delivering 50 L/s when running at 1450 rpm if the…

A:

Q: In a pelton wheel, calculate the power available at the inlet and the hydraulic efficiency of the…

A: H=150 mQ=.06 m3/secD= 750 mm N=800 rpm Cv=1Power P=ρQgH

Q: the diameter of the suction pipe is 385mm. The diameter of the discharge pipe is 268mm. If…

A:

Q: A pump has a displacement of 5.00 in/rev and when driven at 1000 rpm delivers 20 gpm at a pressure…

A:

Q: Calculate the available suction head height of the centrifugal pump from the following data: (1) The…

A:

Q: a pump at 1750 rpm delivering 600 rpm aganist a total head of 200 tt. change in the filling system…

A:

Q: Q-- Consider the following data relating to performance of a centrifugal pump: speed 1200 rpm, flow…

A: Write the given data. N1=1200 rpmQ1=30 L/sH1=20 mP=5 kWN2=1500 rpm

Q: A manufacturing company uses a 100 bar hydraulic power system which supplies 10 liter/minute of oil…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.