A centrifugal pump has d1 = 7 in, d2 = 13 in, bị = 4 in, b, = 3 in, ßi = 25°, and B2 = 40° and rotates at 1160 r/min. If the fluid is gasoline at 20°C and the flow enters the blades radially, estimate the theoretical (a) flow rate in gal/min, (b) horsepower, and (c) head in ft. %3D %3D %3D

A centrifugal pump has d1 = 7 in, d2 = 13 in, bị = 4 in, b, = 3 in, ßi = 25°, and B2 = 40° and rotates at 1160 r/min. If the fluid is gasoline at 20°C and the flow enters the blades radially, estimate the theoretical (a) flow rate in gal/min, (b) horsepower, and (c) head in ft. %3D %3D %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Given: Two (2) identical pumps connected in parallel has the following data: Suction Pressure…

Q: The BEP for a pump operating at 1750 RPM with a 13-inch impeller is 1000 gpm, 150 ft. Using the pump…

Q: (a) flow rate, in gpm; and (b) horsepower. Assume near-radial entry flow.

Q: A two-lobe rotary positive-displacement pump, similar to that of Fig, moves 3.64 cm3 of tomato paste…

A: Given data

Q: Problem 5.13 What is the actual displacement of a 6" x 4" x 10" direct-acting simplex pump in…

Q: Q.1 Acentrifugal pump running at 500 rpm and at its maximum efficier is delivering a head of 30 m at…

A: To find: The head H in meters and flow rate Q in liters per minute at maximum efficiency. Given: The…

Q: A centrifugal pump has the following specifications: d1 = 12 in., d2 = 24 in., b1 = 2 in., b2 = 1…

A: Draw a diagram showing the inlet velocity triangle. Here, u1 is the blade velocity at the inlet, v1…

Q: Ah against capacity Q pump and system curves for both pumps running on the basis of the O1. Two…

Q: consider the following conditions: a centrifugal pump has diameters d1 = 7 in, d2 = 13 in, blade…

Q: the jet ratio is approximately 12. Find the size of the jet, mean diameter of runner, synchronous…

Q: A centrifugal pump operating at sea level develops 50 m of head at 1,200 rpm. It is used to pump…

A: Given data:

Q: (d=0.85, -0.01 Pas and P-90 kPa abs.) from an open pressurized tank B, as illustrated in Figure 1. A…

A: NA

Q: ### Based on the study of pressure losses in pumps and pipelines: Q122. Find the catalogued model of…

A: To find a suitable centrifugal pump based on the specified parameters, it is essential to consult…

Q: Lecture Example 2 : An 18-in-diameter centrifugal pump, running at 880 rev/min and 156 brake…

A: Given :diameter of pump D = 18 inspeed of the pump initially, N1 = 880 rev/minBrake horsepower, P =…

Q: Q5/ A centrifugal pump impeller runs at 1500 rpm & has internal & external diameters of 0.2 n & 0.4…

A: A centrifugal pump is a mechanical device that moves a fluid by transferring rotational energy from…

Q: Q3: a: A centrifugal pump used to take water from reservoir to another through 800 m length and 0.15…

Q: The performance data of a water pump follow the curve fit Havailable =Ho +aV², where the head…

A: Havailable=Ho+αV2.............equation…

Q: A centrifugal pump rotates at n = 1160 rpm. Water enters the blades radially. The outlet radius is…

A: Given:Pump speed, n=1160 rpmOutlet radius, r2=9 in=912ft=0.75 ftBlade width, b2=2 in=212ft=0.1667…

Q: A course in Turbomachinery. ..Lecturer: Dr.Naseer Al-Janabi 21 125 J/kg and Total to Total…

A: Fluid Mechanics: It is a branch of physics in which concerns with mechanics of fluids and forces…

Q: What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with…

A: Solution is attached below:

Q: The three-lobe (on each rotar) rotary pump moves 0.145 gal of a coal slurry in each lobe volume…

A: Given data: Slurry displaced per lobe, Vslurry=0.145 galNumber of lobes=3Speed of rotation, n=220…

Q: P3: Following are the values of some parameters of a centrifugal pump installation, Calculate the…

A: GivenHS=4mHD=15mhsL=2mhDL=5mQ=60ltr/s=0.06 m3/sSG=0.89η=0.82N=1200rpmd=30cm=0.3m

Q: In a test of the centrifugal pump shown in Fig. below, the following data are taken: py =100 mmHg…

A: The velocity of the fluid at inlet by using the continuity equation The velocity of the fluid at…

Q: Two(2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95…

Q: A certain centrifugal pump was tested and its performance curves can be approximated as follows: H…

A: INTRODUCTION: Pumps are used to raise water and transport it to its final destination. Pumps are…

Q: The centrifugal pump speed is changed when the impeller size is constant. The initial flow is 200…

Q: Q4) A) A radial, multistage, four impellers, keyed to the same shaft, centrifugal pump is…

Q: A pump, geometrically similar to the 12.95-in model inFig. , has a diameter of 24 in and is to…

A: For water, ρ1 = 1.94 slug.ft3For gasoline, from Table A.3, ρ2 = 680 kg/m3 = 1.32 slug.ft3 From…

Q: If a pump discharges 70 GPM of water whose specific weight is 61.5 lb/ff° at local g= 31.9 ft/s,…

A: Given data: Pump discharge = 70 GPM = 70 x 0.133681 ft3/min = 9.357639 ft3/min Specific Weight =…

Q: In a test of the centrifugal pump shown in Fig. , thefollowing data are taken: p1= 100 mmHg (vacuum)…

A: Convert 100 mmHg = 13332 Pa, 500 mmHg = 66661 Pa, 180 gal/min =0.01136 m3/s. Calculate the inlet…

Q: Question : An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N =…

A: The given information in the problem is represented in the tabular form in below attached image:

Q: Two pumps (Pump A and B) have performance curves which can be approximated by the following…

A: HA= 340 - 1.2Q2HB= 360 - 2.5Q2

Q: II. Example TDH & WHP Calculation Determine TDH and WHP for a centrifugal pump discharging into the…

A: Solution:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: An irrigation line carries water from a lake down into an arid valley 810 ft below the surface of…

Q: Formaller, + as 29 Zz + hpompaf +z + hearbing + hg.soplam Re = P.V.D Pg 6.9 -1.8 log Re hg.yerel…

A: Given Data⇒ Manometric head (h)=12 m Flow rate (Q)=7500Litmin Convert from Litmin to m3s Divide Flow…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

P11.17 A centrifugal pump has d1 = 7 in, d2 = 13 in, b = 4 in,
b2 = 3 in, ß1 = 25°, and ß2 = 40° and rotates at 1160
r/min. If the fluid is gasoline at 20°C and the flow enters
the blades radially, estimate the theoretical (a) flow rate
in gal/min, (b) horsepower, and (c) head in ft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

Step 2 Calculation

Step 3 Calculation

Step 4 Calculation

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What will be the rated capacity (in gpm, whole number) of a 4.5-inch impeller centrifugal pump operating at aspeed of 3450 rpm capable of generating a head of 60ft of water?
Two pumps (Pump A and B) have performance curves which can be approximated by the following equations: H_A = 340- (1.2(Q^2)), in feet H_B = 360 - (2.5(Q^2)), in feet where Q is in ft^3/s. If pumps A and B were to operate in parallel as depicted in the figure below, at what head (in ft.) should either pump be operated? ... Pump A Round your answer to 2 decimal places. J Pump B
Given: Two (2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95 Bars Suction Pipe Dia = 450mm Discharge pipe Dia = 480mm Velocity of Water = 4.25 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and QT = Total Flow Rate
You and your workmate are choosing pumps for your design. You've already decided which centrifugal pump you will use. The next thing you would think about this time would be the shape of it's impeller blades. The impeller in your design would have a revolution of 565 rpm, will have a volume flow rate of 11.7 gals per min and will (discharge) head of 2222 cm. Your coworker said that axial flow pump is your choice. Would you agree? Why or why not? Prove it.
This is an easy question
Suppose the pump of Fig. is situated between two large water tanks with their free surfaces open to the atmosphere. Explain qualitatively what would happen to the pump performance curve if a valve in the piping system were changed from 100 percent open to 50 percent open, all else being equal. Repeat for the system curve. What would happen to the operating point—would the volume flow rate at the operating point decrease, increase, or remain the same? Indicate the change on a qualitative plot of H versus V. , and discuss.
A six-centrifugal pumps delivers 0.1 m^3/s against a total head of 480 m. What is its specific speed if it routes at 1450 rpm? What type of impeller would you recommended for the pump? Draw velocity triangles for centrifugal pump at inlet and outlet. Drive expressions for power input, power output and efficiency for Francis turbine using flow velocity triangles.
Hydrodynamics pumps 5. A centrifugal pump has r1 = 6 in., r2 = 12 in., b1 = 3 in., b2 = 2 in., β1 = 20°, β2 = 10° and rotates at 1200 rev/min. If the fluid is water at 60°F, estimate the theoretical (a) flow rate, in gpm; (b) the head in ft; and ( c) the water horsepower, HP. Assume near-radial entry flow. a. flow rate Answer : ____________________ gpmb. head Answer : ____________________ ftc. water horsepower Answer : ____________________ HP
3.4 Find the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect friction in your calculations
Please answer as soon as possible. Thank yoouu!!
Using the performance curve of pump A given in Example VIc.3.2 (41.5” and 710 rpm) and find: a) total dynamic head of a similar pump (pump B), at peak efficiency, having a diameter of 35 inches. Assume that both pumps A and B are operating at the same speed. b) pump head if pump B is now operating at 1170 rpm. [Ans.: a) H = 192 ft and b) H = 521.5 ft].
Title of the book: Fluid Power, Theory and Applications, 3rd Edition, James A. Sullivan