A cast iron pipe of equilateral triangular cross sectión with side length of 20.75" has water flowing through it. The flow rate is 6000 gallons per minute, and the friction factor for the pipe is f = 0.017. What is the pressure drop in a 100 foot section?

A cast iron pipe of equilateral triangular cross sectión with side length of 20.75" has water flowing through it. The flow rate is 6000 gallons per minute, and the friction factor for the pipe is f = 0.017. What is the pressure drop in a 100 foot section?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Specifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe in the one inch branch is 8 ft. Brine (sg=1.04, m=10-3Pa*s) flows at 250gpm through the entrance at point A. Assume fully turbulent flow in both branches (f=ft). Pipes are standard Schedule 40 steel pipes. Assume the globe valve is partially shut so its equivalent L/D is 1000. For Part 1 of this project, you are tasked with determining the following: The flow rate in both branches The pressure drop in both branches The overall resistance coefficient
Plz correct solution.
The diagram shown illustrates the flow in a circular metal duct 20 feet long. The duct has a sudden contraction at the inlet and sudden expansion at the outlet. The diameter of the duct is 10 inches and the flow rate is 600 cfm. The duct is such that both ends have area ratio of 0.6. Thus A2/A1 = A3/A4 = 0.6. Calculate:(a) Pressure loss in the duct due to sudden contraction (in. wg.).
State clearly your assumptions in your solution sheet
In the figure below, assume the pipe from B to C has a diameter of 4-inches, (f = 0.035), and length of 18-feet. The pipe from DE is 187-feet, has a diameter of 4-inches and friction factor of 0.035. The Az = 69-feet. The elevation of C is 14-feet above the lower water surface. If the pressure head @ C is to be no less than (-) 20 feet, and the pump has 63% efficiency, what horsepower must be supplied to the pump in order to convey flow through the system? (Kent = 0.8) Assume a submerged exit. Az
A major water main is an 18-in ductile iron pipe. Compute the Reynolds number if the pipe carries 16.5 ft/s of water at 50°F.
Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
Water is transported for 500 m in a 4 inch ductile iron pipe (coated) with a flow rate of 0.04 m3/s. Calculate the pressure drop over the 500 m length of pipe. (Calculate the friction factor f using the formula given in class notes/textbook, and not by using the Moody chart).
The diagram shown illustrates the flow in a circular metal duct 20 feet long. The duct has a sudden contraction at the inlet and sudden expansion at the outlet. The diameter of the duct is 10 inches and the flow rate is 600 cfm. The duct is such that both ends have area ratio of 0.6. Thus A2/A1 = A3/A4 = 0.6. Calculate: Total pressure loss in the duct (in. wg.).
Water at 80°F flows from a storage tank through 618 ft of 6-in Schedule 40 steel pipe, as shown in the figure. Taking the energy loss due to friction into account, calculate the required head hin feet above the pipe inlet to produce a volume flow rate of 1.65 ft³/s. (round the final answer to three significant figures) h 6-in Schedule 40 steel pipe pipe length