A carpenter holds a 11-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board, determine the forces at A and B (use positive if the force is up and negative if down).

Q: Lloukle Inte gr ation Meth od Lletermine the ff :). LDefle etion at e). Mope at C

A:

Q: What are the values of D10,D30 & D60 in the given two graphs,where the blue line represents the…

A: D60 - Size of the soil grain corresponding to the 60%finer.  D30 - Size of the soil grain…

Q: Fastly calculate the value of displacement Work done=20 J force%33 N

A:

Q: I need the correct answers gor g1 = -2.00% and g2 = +2.00%

A: g1= -2%g2= +2%PVI Elevation = 750 ft and station = 30+00Fixed elevation, y = 753 ft and station…

Q: Hook's Law

A:

Q: 5. The area of a rectangle is 20 sq.cm and one of its sides is 4 cm long. Find the width and…

A: Given the area of rectangle =20 sq.cm Given one side, let a = 4 cm We know that area of rectangle =…

Q: For the given figure, the dimensions are given in meters. Calculate the following using integration:…

A:

Q: Q2: use the inverse method to find the vlaue of X, Y and Z for the follwing equations: 2x-y+223D1…

A:

Q: Use bisection, newtons, secant and regula falsi methods.

A: AS EQUATION IS GIVEN WE NEED TO SOLVE BY DIFFRENT METHIOD AS B PART HAS TO BE TAKEN MEANS BETBEEN 1…

Q: 0.9 Chart Title 0.8 0.7 0.6 Height (m) 0.5 0.4 0.3 0.2 0.1 0 0.00 0.01 0.02 0.03 0.04 0.05 0.07 0.06…

A: The problem asks to identify and find the values of the quantity identified by the two lines. The…

Q: Find the general solution of the equation (by Homogenous Method) : (x+2y)dx =(2x+ y)dy

A:

Q: What reduction factor are we going to use if p > Pb a. 0.9 b. 0.65 c. 0.45 d. Ø= 0.65 +0.25 Ey Et…

A: Given:-ρ>ρbTo find:-reduction factor

Q: tographs at a scale of S are required to cover an area X-mi square. camera has a focal length f and…

A: Photographs at a scale of S = 1:6200 are required to Cover an area X= 8 mi2The camera has a focal…

Q: Three couples are applied to a box as shown below. The box has sides x = 80.0[mm],y= 50.0 [mm] and z…

A:

Q: omn ample-2 For measuring the area of a figure using planimeter, the as placed outside and the…

A:

Q: A box having a mass of 3 slugs was initially at rest when a 22.500-pound horizontal force was…

A: Given above data we have to find displacement

Q: • Determine the x. Measure it from the y-axis.

A: A channel section is shown in figure Required- to determine the position of centroid from y- axis.

Q: answer asap divide the figure, know the x and y each figure. plz illustrate the x and y of each…

A:

Q: How were the equations in the table of "visual work product integration" derived? /in other words…

A:

Q: 4. Every moming Joy walks to school from her boarding house and takes only a single route. For five…

A: GIVEN :- No. of paces on Monday = 345 No. of paces on Tuesday = 353 No. of paces on Wednesday = 358…

Q: With respect to the given X & Y axis of the shaded section.

A:

Q: Find the magnitude of the resultant of the concurrent forces if 0 = 24.19°,B = 35.43°, F = 134.4, Q…

A:

Q: Calculate the following: xbar (location of the centroid along x axis), m ybar (location of the…

A: solution given next step

Q: A pipeline is to be built from a point on the bank of an 800m wide river to a point 3km downstream…

A: Width of river, w = 800 m = 0.8 km Also, x + y = 3 km Under the river, the cost per km = $ 750000…

Q: b=480mm d=700mm fc'=30MPA fy=400MPA Mu=1430kN-m Determine As A. USE NSCP 2015, As = sq.mm. B. USE…

A:

Q: RA= RB= Vmax= KN 2 decimal places KN 2 decimal places KN 2 decimal places

A:

Q: 2. Which of the following is not a property of the mean? a. at least the interval scale of…

A: Mean is the average value of all the given values

Q: Q2/ Measure the area of given plot in a dimension paper given. All dimensions are in mm. (2 Marks)…

A: First divide the given area into four possible parts, find the individual area of four parts and sum…

Q: Please

A:

Q: Find: 1. The magnitude of the 150N load is, 2. The direction of the 150N load is LB. a. NOTE: i. Use…

A: Consider the figure,

Q: Q1:- Compute the area of each part by using the proper formula. Then find the total area in…

A: Calculate area of each segment and then determine total area by adding the area of each section.

Q: Calculate the following: xbar (location of the centroid along x axis), mm ybar (location of the…

A: To find centroid and area

Q: 1400 1200 1000 800 600 400 200 1000 2000 3000 4000 5000 6000

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.