A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1400 lbf/in.², and saturatedvapor enters the turbine (state 1). The condenser pressure is 1.2 lbf/in.² The mass flow rate of steam is 5.5 x 106 lb/h. Data at keypoints in the cycle are provided in the accompanying table.Determine:n =i 72.2705State p (lbf/in.2) h (Btu/lb)%1232₂414001.21.214001174(a) the percent thermal efficiency.(b) the back work ratio.(c) the net power developed, in Btu/h.(d) the rate of heat transfer to the working fluid passing through the boiler, in Btu/h.Determine the percent thermal efficiency.758.3446.5598.8

Givn that: The pressure at different stage: p1=1400 lbf/in2 p2=1.2 lbf/in2 p3=1.2 lbf/in2 p4=1400…

A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1400 lbf/in., and saturated vapor enters the turbine (state 1). The condenser pressure is 1.2 lbf/in.² The mass flow rate of steam is 5.5 x 105 lb/h. Data at key points in the cycle are provided in the accompanying table. Determine: State p (lbf/in.2) h (Btu/lb) 1 2 3 4 1400 1.2 1.2 1400 1174 758.3 446.5 598.8 (a) the percent thermal efficiency. (b) the back work ratio. (c) the net power developed, in Btu/h. (d) the rate of heat transfer to the working fluid passing through the boiler, in Btu/h.

A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1400 lbf/in., and saturated vapor enters the turbine (state 1). The condenser pressure is 1.2 lbf/in.² The mass flow rate of steam is 5.5 x 105 lb/h. Data at key points in the cycle are provided in the accompanying table. Determine: State p (lbf/in.2) h (Btu/lb) 1 2 3 4 1400 1.2 1.2 1400 1174 758.3 446.5 598.8 (a) the percent thermal efficiency. (b) the back work ratio. (c) the net power developed, in Btu/h. (d) the rate of heat transfer to the working fluid passing through the boiler, in Btu/h.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

For the heat pump (used for heating) illustrated below, what is its coefficient of performance for heating. Ag? The gas is monatomic. p(Pa) 6 A. 8/3 B. 2 C. 11/3 D. 14/3 E. 19/7 2 V(m³) 34
A pressure versus volume (pV) diagram for a system is shown in the figure. The arrows of the curve indicate the direction of the process, and the points of interest are labeled. The values for the points in the diagram are shown in the table. Volume (m³) Pressure (Pa) 2 Vo = 27.8 po = 1.37 × 10ª Vi = 20.8 Pi = 1.37 × 104 V2 = 17.4 P2 = 6.18 × 10³ V3 = 13.9 P3 = 6.18 × 10³ V4 = 13.9 P4 = 2.64 x 103 Vs = 8.87 p5 = 1.00 x 10³ Volume (m) Calculate the amount of work done on the system from 0–2 (Wm) and then for the entire curve from 0-5 (Wos). Pressure (Pa)
Do it fast
Q4- Water in piston cylinder system at (TI and X1). The water is heated isothermally until the(V2=4V1). Then the work is exchanged with system according the low (PV=C) until reach to itsoriginal pressure. Assume TI and XI and draw the processes on P-v diagram and determine1- The final volume2- The amount of work
A gas expands from I to F in the figure below. The energy added to the gas by heat is 302 J when the gas goes from I to Falong the diagonal path. Three paths are plotted on a PV diagram, which has a horizontal axis labeled V(liters), and a vertical axis labeled P (atm). The green path starts at point I (2,4), extends vertically down to point B(2,1), then extends horizontally to point F (4,1). The blue path starts at point I (2,4), and extends down and to the right to end at point F (4,1). The orange path starts at point I(2,4), extends horizontally to the right to point A (4,4), then extends vertically down to end at point F(4,1). (a) What is the change in internal energy of the gas?J(b) How much energy must be added to the gas by heat for the indirect path IAF to give the same change in internal energy?J
1.50 mol of an ideal gas with a constant ratio of heat capacities at constant pressure and volume y =2 = 1.40 is taken through the (reversible) cycle shown in the figure below. The process A - B is an expansion at constant temperature, whereas B →C and C → A are constant-pressure compression and constant-volume processes, respectively. 040 a) What is the temperature TA of the gas at A? P (atm) For the cycle as a whole, Isothermal b) calculate the (net) work done W (by the gas), 04021 c) calculate the (total) heat transfer Q, process d) find the change in the (internal) energy U of the gas, B e) verify that the 1" law of thermodynamics C is satisfied. 1 liter=1.00x10 m , 1 atm=1.01x105 N/m² , kɛ = 1.38x1023 J/K , NA=6.02x1023 mol. -V (liters) 50 10
When air expands adiabatically (without gaining or losing heat), its pressure P and volume V are related by the equation PV to the power of 1.4 = C where C is a constant. Suppose that at a certain instant the volume is 480 cubic centimeters and the pressure is 75 kPa and is decreasing at a rate of 10 kPa/minute. At what rate in cubic centimeters per minute is the volume increasing at this instant? Please Write legible
Please solve this question in 30 minutes but correctly
The heat engine shown in the figure uses 2.0 mol of a monatomic gas as the working substance. (Figure 1) Figure p (kPa) 600 400 200 0 0 0.025 0.050 < 1 of 1 V (m³) Part D Determine AEth, Ws, and Q for 3→1. Enter your answers numerically separated by commas. Express your answer using two significant figures. VE ΑΣΦ AEth, Ws, Q = Submit Part E Request Answer What is the engine's thermal efficiency? Express your answer using two significant figures. ? J
Look at the P-V diagram below (Diagram 1). Calculate the work done by the gas for the paths A, B and C. Assume that in Diagram 1, P1 = 1 atm, P2 = 4 atm, V1 = 5 L, V2 = 15 L. a) WA = 1013 J, WB = 0, WC = -2533 J b) WA = 0.01 J, WB = 0, WC = -0.025 J c) WA = 2533 J, WB = 0, WC = -1013 J Calculate the work done by the gas for the path AB in Diagram 2. Use the data: P1 = 1 atm, P2 = 4 atm, V1 = 5 L, V2 = 20 L. (Path AB is an "isothermal" which means the temperature T is constant on this path). a) 0.012 J b) 1220 J c) 0.0278 J d) 2809 J
A container is filled with an ideal diatomic gas to a pressure and volume of P1 and V1, respectively. The gas is then warmed in a two-step process that increases the pressure by a factor of five and the volume by a factor of four. Determine the amount of energy transferred to the gas by heat if the first step is carried out at constant volume and the second step at constant pressure. (Use any variable or symbol stated above as necessary.)
The table above shows the measurements taken while in ideal gas underwent an iso volumetric process fill in the values for table