A car starts from rest with an acceleration of 6.3 m/s² which decreases linearly with time to zero in 9.8 seconds, after which the car continues at a constant speed. Determine the time t required for the car to travel 300 m from the start. Answer: t - i s

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…

A: Center of mass: The Center of mass is the point on a body about which it is assumed that the total…

Q: In the figure below, explain the case where the dimension tolerance is satisfied, but the plane…

A:

Q: 1. For the following part sizes and geometric tolerances, determine the appropriate geometric…

A: Givenϕ 2.062-0.0050.00⊥-Perppendular Toleranceϕ⊥=0.002

Q: The results of a tensile test are: Diameter of the specimen Gauge length Load at limit of…

A: Given: The diameter of the specimen is, d=10 mm. The value of gauge length is, l=40 mm. The load at…

Q: On the part below, with only the limits of size specified, what coaxiality tolerance is implied…

A: In this problem, it is asking about the co-axially tolerance between the two diameters.

Q: The rectangular coordinates of a particle which moves with curvilinear motion are given by x =…

A: Givenx=10.25t+1.00t2-0.25t3y=6.10+16.04t-2.29t2t=4sθ=28o

Q: Problem (13): Determine tolerance value and limit dimension of the rod which a diameter is ∅6 mm,…

A: Given Data Diameter of shaft is : d=6 mm T=d9 es=-40.64=-0.04064 mm ei=-76.20 mkm=-0.07620 mm Now…

Q: following statements, answer True or False and explain the answer briefly. The tolerance of…

A: Yes, it's true. The tolerance of standard mass used must be smaller than the uncertainty of…

Q: Using slip gauge set (BM1- 447 -11) shown in the tabular column(below) select suitable slip gauges…

A: For the work piece of 44.73 mm size we can take the slip gauges in this order :-

Q: Enumerate at least 20 G-CODES and 10 M-CODES and write their description. Create a table to organize…

A: Given question: Enumerate at least 20 G-CODES and 10 M-CODES and write their description G Codes are…

Q: A rectangular block 100 mm x 150 mm has a hole with diameter 60 mm at the center. The hole tolerance…

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: answer both questions , thank you

A: A) Geometric tolerance = difference between ideal dimension and actual dimension  Ideal dimension =…

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: In the figure, one end of a uniform beam of weight 340 N is hinged to a wall; the other end is…

A:

Q: Calculate the tolerances and allowances for a shaft with a diameter of 40 mm with a tolerance area k…

A:

Q: Problem (2): Determine tolerance value and limit dimension of the rod which a diameter is Ø47 mm…

A: Given data: The diameter of the rod is d = 47 mm. The limit deviation is D = 47.6 mm.

Q: Choose the LETTER from the stress strain graph that matches the stress strain graph attributes…

A: Stress-strain curve of material provides us the information about the stress and strain in material…

Q: Given the measured value is 20.04mm and the true value of the measured dimensionis +-(plus minus)…

A: Firstly, we get to know about Measured value and True value: Measured value: The value which is…

Q: 29. If two planar surfaces are apart from each other by a dimension with a tolerance of t 0.0.05,…

A:

Q: 62.7 g/cm3 to slug / ft3

A:

Q: Problem (7): Determine tolerance value and limit dimension of the rod which a diameter is ∅25 mm,…

A:

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: . An LVDT is used to measure the axial deformation of the simple bar of Fig below. The uncertainty…

A:

Q: Calculate the average fall time and standard deviation using the data above. Average - 1.5s Stdev-…

A: Given information: The average fall time (t) = 1.5 s Standard deviation (sd) = 1.85 s acceleration…

Q: For the following part sizes and geometric tolerances, determine the appropriate geometric tolerance…

A: A.    Geometric tolerance = 0.005 + 0.007                                     = 0.007…

Q: On the drawing attached, what is the coaxility tolerance that is implied between the two diameters…

A: Given: ∅O=30/30.2∅I=12/12.3To find:Coaxility tolerance

Q: Complete the following table. Show your calculation and draw Go -Not Go representation.

A:

Q: 2310. mm as the Iimits for afts. The natural tolerance is found to be a -distributed random variable…

A: Given that ,μ=25mmXo=25.05mmR=98%

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅6 mm, according to the…

A: Given Data Nominal diameter of rod is : d=6 mm Upper deviation is : es=-40.64 mkm=-0.04064 Lower…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Calculate the moment of inertia of the shaded area about the x-axis.

A:

Q: The motorcycle has a kerb mass of 239 kg and test rider's mass was recorded as 76.35 kg. The wheels…

A:

Q: Transcribed image text: Q 1/ The basic size of two comparable parts with the tolerance code for each…

A:

Q: Problem 4: Metal sheet paper is cut to a width of 205 cm with a tolerance of +/-05. The cutting…

A: The little positional difference that occurs when sheet metal is cut is known as profile cutting…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.