A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume LAB = 2.0 ft, LBC = 6.0 ft, w= 1560 Ib/ft, P = 2000 lb, b = 13 in., d = 8 in., t =%3D%3D0.40 in. Determine(a) the maximum horizontal shear stress.(b) the maximum compression bending stress.(c) the maximum tension bending stress.PbВCdLABLBCAnswers:(а) Tmax2.28ksi(b) ОС,max-5.88ksi(с) ОТ,max2.15ksiII

Taking moments about C, we get So, the maximum Bending moment acting at support C of cantilever =…

A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume LAR = 2.0 ft, LBC = 6.0 ft, w = 1560 Ib/ft, P = 2000 Ib, b = 13 in., d = 8 in., t = 0.40 in. Determine (a) the maximum horizontal shear stress. (b) the maximum compression bending stress. (c) the maximum tension bending stress. b A B d LAB LBC Answers:

A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume LAR = 2.0 ft, LBC = 6.0 ft, w = 1560 Ib/ft, P = 2000 Ib, b = 13 in., d = 8 in., t = 0.40 in. Determine (a) the maximum horizontal shear stress. (b) the maximum compression bending stress. (c) the maximum tension bending stress. b A B d LAB LBC Answers:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An embedded beam is subjected to the loads shown. Determine the stress produced at points A, B ,C, D in the embedment section. The X axis is 72.9 mm from the top edge. Solve correctly please
Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB=LCD=2.0 m, LBc=6.9 m, P=19 kN, bf=180 mm, t₁=14 mm, tw=9 mm, d=159 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. A Answers: OmaxT maxC = LAB i i P B LBC bf + Cross section MPa MPa P LCD D X
Flexure stress *please answer in complete solution and Draw the FBd properly and neatly *
PROBLEM No. 2 The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. If a 20-kip load is applied, determine the vertical displacement in the bar at A and C that will cause a stress in the rod at C to be 50 ksi. Indicate the direction of movement. Use E = 29x106 psi for steel. (Provide FBD and movement diagram in your computation). A = 0.5 in.? 3 ft | A B D | 20 kips te 2 ft -→-- 2 ft -→l 4 ft 4 ft A = 0.75 in.²
A 62.6-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used oy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. B D 1.5 m The smallest allowable dimension dis mm.
The beam shown below has a cross section of channel shape with width b=200 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. And draw. 200 mm 3.2KN/ 2 KN.M BO 80mm 12mm 3m 1.5m
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
The beam shown here is made of wood with an allowable shear stress of τall = 1100 psi. If PB = 5 kips, determine the maximum allowable force PC that can be applied on the structure before the beam fails in shear.[LAB= 2 ft, LBC= 2 ft, LCD= 1.5 ft, b = 1.25 in., h = 7 in.] Determine the maximum value of the first moment of area (Q) for the beam. (in^3) Determine the maximum allowable force at C (PC) that can be applied on the structure before it fails in shear. (kips)
A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 15 ft b = 8 ft C= 10 ft P= 12500 Ib Q= 5000 lb The moment of inertia of the cross section is i, = 110 in.". Determine the magnitude (ie, the absolute value) of the maximum compressive bending stress in the beam. TT 3.2 in. B D 5,8 in. Answer: Omax (Compression) = 1 psi %3D
Please write All answer in mpa