A cantilever beam must be designed to carry the loads shown below. 1. Design the beam for flexure. Determine b, h, As and bars to provide the required steel. Draw a cross-section of the beam to show placement of the flexural steel

Q: Explain a bernullies beam with equation(s)

A: Bernoulli's beam, also known as the Euler-Bernoulli beam, is a concept in structural engineering…

Q: Describe what is least cost method (LCM) steps of LCM in transportation?

A: Least cost method (LCM) -  The method used  to find the initial feasible solution for the…

Q: |P D E A В -L/2 L/4→L/4→ |

A: let,RA=vertical reaction at support ARB=vertical reaction at support Busing equilibrium…

Q: 24 kips 60 kips 36 kips B C D E F kips A 9'- 9'- ° HA G 9 24 kips 12'

A:

Q: 1. Using the method of joints, determine the force in each member of the trusses shown. State…

A: To find force in all the members of the truss

Q: Identify the zero force members in the truss shown. Using the method of sections, determine the…

A: If at a joint 3 members meet and there is no external load or support condition at that joint then…

Q: Prepare a summary for usage of flood barrier during flood.

A:

Q: 1. Determine the force in bars BD, CD, and DE of the nacelle truss shown below. Indicate whether…

A:

Q: te t for Tension and C for Compression). ]12 kN 4 m B 6 kN 4 m C E I K 6 @ 3 m

A:

Q: Find the axial forces at CG, DH, GH, BC, and BG in the truss shown below: 2m 2m 2m 2m C B D 1m E 1m…

A:

Q: 4 kN 60° D E G A C В - 2 m - 2 m -

A:

Q: Which joint would be the best place to start your analysis of the truss shown?

A:

Q: roblem – Determine the force in each member of the truss shown below C F= 100 kips 1S ' B. 15' D 20…

A:

Q: Draw the Free Body Diagram for the structure below. 3'-0" A7 Pin support 800 lb 5' 0" 60⁰ 500 lb…

A:

Q: Problem # 2: Determine the internal axial force in each member of the truss using the force method.…

A:

Q: The Fink truss is supported by a hinge at A and by rollers on a 1 to 2 slope at B. The bracing bars…

A:

Q: dentiry the shown. (Enter your separated E A

A:

Q: DETERMINE THE FORCE IN EACH MEMBER BY THE METHOD OF JOINTS. F B 40 KN 4 at 3m - 12m OF TRUSS SHOWN…

A: Given data  Find force in each member using method of joint

Q: P P – L - 6 in. (1) (2) 0.5 in.-

A: Given data: width = 6 in.

Q: Compute the force in members CE, BD, and CD by method of sections in the truss shown.

A: Given:- To find:- Force in CE, BD and CD Tension and compression member forces signs : Away from…

Q: Beam is gm long, madde ed steel and is supporbeel by tuo' supports. Mass f Bie beam i's 2500 kg.…

A: Beam's self weight will act as udl over the entire span. w = Self weight = Weight of beamSpan of…

Q: For the truss shown, a) By inspection, identify the zero force members in the truss. b) Use the…

A: Consider the free body diagram of the truss shown below.

Q: Problem 20 k G y 10k E 15 ft F 10k russ is subjected to the following forces as pwn. Determine: 10…

A: To find the support reactions and resultant force-

Q: Assume the support at B is a roller. Point C is located just to the right of the F = 8-kip load.…

A: Determine the normal force, shear force and bending moment at point C. Note:- point-C is just to the…

Q: Gove a short description of the structures roller support and truss

A: Objective:To provide a short description of the structures roller support and truss

Q: Determine the force in bars BD, CD, and DE of the nacelle truss shown below. Indicate whether…

A: Given nacelle Truss with 4 loads 600lb and  1200 lb * 3 Support C is hinged and support F is roller…

Q: 1. Portal Method The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X…

A: The assumption in the portland method:- For each storey of the frame, the interior column will take…

Q: The beam shown is constructed by joining two pieces of wood together using screws. If the resistant…

A: Given:- A beam is constructed by joining two pieces of wood together using screws The resistant…

Q: What type of friction is experienced by bowling ball after thrown? Kinematic Friction Static…

A: A bowling ball experiences rolling friction after thrown. Therefore, the answer is rolling…

Q: 4) Draw the Torsion Diagram for this assembly. A B C D 80 N·m 20 N-m 30 N-m

A: The sign convention for Torsion in shafts follows the right hand thumb rule.Following the right hand…

Q: 80 kN 60 kN 10 m 10 m 10 m L. A B D F 20 C E

A:

Q: 2. Determine the force in members BC, BE and CE of the truss shown using method of sections. 130 Ib…

A:

Q: Determine the forces BG, DF & BC of the truss using method of joints. 80 k 80 k 20k 8ft 80 k 80 k 8t…

A:

Q: Please answwer the question in the picture, Show all of your work please.

A: Follow the steps...Image_1Image_2Image_3As calculated above Absolute Maximum SF =17 kipAbsolute…

Q: 5. Method of Sections: Using the method of sections (no other method is acceptable), determine the…

A:

Q: Determine the force in members DF, FG, and Gl of the triangular Howe truss shown in figure below.…

A:

Q: K 15 ft A |C ID E. 3k -5@9 ft = 45 ft

A: Truss is axial force resistant structure, so all the member of truss always resist force by means of…

Q: kindly solve only subpart LETTER D. with a complete solution for verification purposes. Thank you…

A:

Q: INTERNAL FORCES – BEAM ACB d) Draw a diagram of member ACB with all external forces acting on it,…

A:

Q: Q5 (10 Marks): Determine the force in each member of the truss. State if the members are in tension…

A: Consider the truss as shown below ; 1. Now consider Joint C ; Fy = 0  FBC×67.21 = 400  FBC = 400 ×…

Q: Question 2: For the following truss: a) Calculate the degree of static indeterminacy (SI) and state…

A:

Q: Using

A:

Q: Q/: By the method of section, compute the bar forces in the lettered bars of thee trusses. 100 15 ft…

A: To solve for the force developed in member 'a'

Q: Can you please find out the force in each member of the truss. Also can you please State if the…

A: Given data: