A cantilever beam is subjected to an inclinedforce (P) as shown in Figure 1, the equilibriumnormal force component on the cross-sectional area at the point A is (in kN)Figure 1:P 400 kN301000 mmAArea 30 mm20 mm In Figure 1, the normal stress on the cross-sectional area is (in Mpa)الاختیارات597 O567 O587 O577 O

Force P = 400 kN=400*103 NCross section area, A=30 mm * 20 mmInclination of force P, θ=30o

Answered: A cantilever beam is subjected to an…

A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal force component on the cross- sectional area at the point A is (in kN)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A simple beam is shown in Figure Q2(a) has three concentrated loads at the position indicated. The…

A: Given- Diameter (d) = 200 mm Let support reaction at support 1 and 2 be R1 and R2 respectively

Q: Figure Q3a shows a simply supported beam AB with support reactions RA and RB. Two point loads F₁ =…

A: To find : The reaction RA and RB . Given : The forces are F1=35 kN and F2=65 KN. The length are…

Q: The horizontal beam ACB with the cross section dimension (width = b) (height = h) is shown on the…

A: INTRODUCTION: This is a basic problem of joints and struts and explained with details of free body…

Q: Draw the shear-force and bending-moment diagrams for a simple beam as shown in Figure Q2 with a…

Q: Anchor of the beam given in the figure is built-in support, B point is movable support and G joint.…

A: Let the reactions at fixed support 'A' be: RAH , RAV , MA. Let the reactions at pin joint 'G' be:…

Q: 75 mm 15 mm

A: given:

Q: Given: the simply supported beam with applied loads below Required: The resultant force of the…

Q: An overhang beam ABC of length 6 m is supported and loaded as shown in Figure Q3.If E = 200 GPa and…

Q: Home Work: 1. Determine the maximum deflection & in a simply supported beam of length L carrying a…

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

Q: alculate the reactions at point A for the beams shown. (Clockwise rotation of a moment - Negative,…

A: Total weight of the udl = 1(14+10)=24K it acts 12' from the A supports Using the conditions of…

Q: In the Figure 5, the equilibrium shear force component at the fixed edge of the cantilever beam is…

Q: A beam with a solid homogeneous rectangular section is simply supported at A and B. A concentrated…

A: F=275 kNL1=3.75mL2=1.25mrectangular section b=45mmd=205mm

Q: Find the support reactions of the beam given in the figure.

Q: To calculate the internal normal force, shear force, and bending moment at a point in a beam. A beam…

Q: respect to end A. CL 3. (201) For the cantilevered beam shown here: w=500 lb/ft; P = 1050 lb; L = 18…

A: For the cantilevered beam shown here: w=500 lb/ft, P=1050 lb L=18 ft.3(a) Sketch a neat and…

Q: shown in Figure 3(a) a roller support channel section as shown in Figure 3b). Determine the support…

A: Since you have posted a question with multiple subpart, so we will solve first three part for you.…

Q: Problem 5.3 The beam is subjected to a load F = 400 N and is supported by the rope and the smooth…

Q: A beam ABCDE is 5 m in length and loaded as shown in Figure Q3. Draw the S.F. and B.M. diagrams for…

Q: the location, y, of the centroid of the composite (use 4 significant figures for all values): area

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

A: According to the details provided in the question, we need to calculate the normal force component…

Q: Find the external reactions at support A (fix-end) for the beam shown in the figure. 7 kN 4 kN/m 30…

A: Given data: Moment=30 kN.m Need to determine the external reactions at support A.

Q: Find bending moment

A: Given; A concentrated load P acts on a simply supported beamof span L at a distance L/3 from the…

Q: - Given the simple beam as shown below. Determine the following: 100 N/m 30 N/m A WITHA. B 2 m 7m…

Q: 4.19-4.24 For the beams shown in Figures P4-19-P4-24, determine the nodal displacements and slopes,…

Q: Ql: Draw the shear force and bending moment for the overhang beam shown in figure below? 4 kN /m

Q: A triangular distributed load of max intensity w-490 N/m acts on beam AB. The beam is supported by a…

A: Given:The maximum intensity of the triangular distributed load,

Q: The simply supported beam with a rectangular cross-sectional area is designed to support the loading…

Q: A beam with simply supported is subjected to a trapezoidally distributed load as shown in Figure…

Q: 3. A beam is loaded as shown. El is constant. The vertical reactions at B and C are equal to 80kN.…

A: given; at point A force(F1)=40KN at point D force(F2)=40KN weight…

Q: 1. Determine the maximum deflection d in a simply supported beam of length L carrying a uniformly…

Q: 2. For the 20 meter beam shown, there is a roller at "A" (Ay = 52 kN; it is acting upward), and a…

A: For the 20 meter beam shown, there is a roller at "A" (Ay= 52 KN; it is acting upward), and a pin…

Q: . The two 12 ft. beams shown are move horizontally with respect to each other and load P shifted to…

A: Consider the diagram as shown below for the given beam.

Q: USE IMAGE BELOW Question; Draw and fully label the Freebody diagram of the BEAM in the picture…

Q: The homogeneous beam shown in the figure is suspended by a cable at point B and is pin supported at…

Q: beam shown in figure below. Also determine the magnitude of the resultant force (Ri, and the…

A: Consider the free body-diagram of the system as shown below.

Q: A 5-m simply supported beam AB supports a trapezoidally distributed load.The intensity of the load…

Q: When a beam has only uniformly distributed forces applied, the moment diagram consists of piecewise…

A: A beam with Uniformly distributed load given

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

A cantilever beam is subjected to an inclined
force (P) as shown in Figure 1, the equilibrium
normal force component on the cross-
sectional area at the point A is (in kN)
Figure 1:
P 400 kN
30
1000 mm
A
Area 30 mm
20 mm

In Figure 1, the normal stress on the cross-
sectional area is (in Mpa)
الاختیارات
597 O
567 O
587 O
577 O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
Q2. Figure Q2 shows the free body diagram of a 10 m long beam AD of uniform cross-section, simply supported at locations A and C. A uniformly distributed load of 10 kN/m is applied on the part AB of the beam together with a concentrated load of 20 kN at the end D. 10kN/m 20kN AV B 4m 4m 2m Fig.Q2: Structural Beam (d) From the SFD drawn in (b), find the distance from point A to the position between points A and B where there is no shear and determine the bending moment at that position. (e) Write the mathematical expression for shear force Vat section X-X between the points B and C which is at distance x measured from support А.
A beam is loaded as shown in the figure below. 1. The reaction R1 is equivalent to: 2. The reaction R2 is equivalent to:
2. Determine the reactions at A for the 2 kN cantilever beam subjected to the 4 kN/m distributed and concentrated loads as shown in figure 2. 3 m 1.5 m 1.5 m- Figure 2.
(a) Calculate reactions at A and B in beam shown in Figure Q17
Figure Q2(b) shows the cross-section of a cantilever beam ABC. The beam is subjected to uniformly distributed loading and a concentrated force as shown in Figure Q2(c). Determine:(i) the second moment of area or moment of inertia for the cross-section about its neutral axis (NA)(ii) the internal bending moment and bending stress at section x-x as shown in Figure Q2(c) and at points P and Q of the cross section as shown in Figure Q2(b) of the beam and state whether the bending stress is in tension or compression.
Q1/ A beam (ABC) is supported at A&B and carries a uniformly distributed loads between AB of 60N/m and downward load of magnitude 40 N at C. Find (RA) & (RB). Take AB= 6m & BC=1m ?
A cantilever beam of length 2 m carries the point loads as shown in Fig 2. Draw the shear force and B.M. diagrams for the cantilever beam. 300 N 500 N 800 N of to D 0.5 m 0.7 m 0.8 m-
Q.4. Draw the load and bending moment diagrams that correspond to the given shear force diagram (figure 4). Assume no couples are applied to the beam.
Example (5): Draw the shear force and bending moment diagrams for the beam shown in Figure (2.13). 6 kN 4 kN/m Hinge D 3m 3m 2m 3m Figure (2.13)
A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal force component on the cross- sectional area at the point A is (in kN) Figure 1: P 400 kN 30 1000 mm A Area 30 mm 20 mm
b. find the second moment of area of a cross section OC. find the centroid of a cross section O d. none of these options If the "I" value of beam cross section is 6,400,000 mm and the maximum distance from the neutral axis of the cross section to the top and bottom edges of the beam cross section is 129 mm, what is the section modulus of the beam? Note: Give your answer in mm³ Note: Do NOT include units in your answer. Answer: X A typical value for the stiffness of aluminium alloy is... Select one: a. 200 GPa b. 72 GPa