A cantilever beam 10 ft long carries a uniformlydistributed load of w= 100 lb/ft. The beam isconstructed from a 3-in.-wide by 8-in.-deepwood timber (1) that is reinforced on its uppersurface by a 3-in.-wide by 0.25-in.-thick alumi-num plate (2). The elastic modulus of the woodis E= 1,700 ksi, and the elastic modulus of thealuminum plate is E = 10,200 ksi. Determinethe maximum bending stresses produced intimber (1) and aluminum plate (2).100 lb/ft10 ftvid bsamCantilever beam with w = 100 lb/ft.(1)3 in.3 in.0.25 in.8 in.Cross-sectionaldimensions.

Given : Length of beam = 10 ft W = 100 lb/ft Width of wood timber = 3 inches Depth = 8 inches Size…

A cantilever beam 10 ft long carries a uniformly distributed load of w= 100 lb/ft. The beam i constructed from a 3-in.-wide by 8-in.-deep wood timber (1) that is reinforced on its upper surface by a 3-in.-wide by 0.25-in.-thick alumi- num plate (2). The elastic modulus of the 1700 ksi, and the elastic modulus of Wood

A cantilever beam 10 ft long carries a uniformly distributed load of w= 100 lb/ft. The beam i constructed from a 3-in.-wide by 8-in.-deep wood timber (1) that is reinforced on its upper surface by a 3-in.-wide by 0.25-in.-thick alumi- num plate (2). The elastic modulus of the 1700 ksi, and the elastic modulus of Wood

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
Please answer fast ASAP
A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
I need the answer to the question in reinforced concrete
DETERMINE THE MOMENT OF INERTIA OF THE BUILT-UP SECTION ABOUT THE INDICATED X. AXIS. The thickness of the stem in problem 2 is 1.5". Please show clear and complete solution in tabulated form. Thank you
Topic: Restrained Beams 140KN 2.5m 3.5m 5KN/m 3.2m МА 6m MB 11WL2 Pab² 5WL2 Pa?b MA = - MB = - 192 L2 192 L2 INSTRUCTION: 1. Determine the maximum stress in the timber beam with the size of 120 x 370mm.
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
The beam AB of length L = 2m is consisted of two attached materials which are a solid aluminum %3D 9. core ( E, = 27 GPa, (tallow), = 80 MPa ) of Da = 10mm and a tubular steel (G =80 GPa, %3D %3D a (Tallow ). = 240 MPa) cover of (D3)inner = 10mm, (D,) outer = 16mm. Determine the maximum %3D %3D S. torsion T that can be applied to the beam at B without causing yielding either in the aluminum core or steel cover a St Al 10mm a (a-a Cross-section) T 16 mm
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
A timber beam 150 mm wide and 200 mm deep is to be reinforced by bolting on two flitched each 150 mm x 12.5 mm in section. Find the moment of resistance when the flitched are attached symmetrically at the top and bottom. Allowable stress in timber is 6 N/mm². (Es= 20 Ew)
Reinforced concrete design plz answer the a and b with complete solutions.. thank you