Q1.A call processor in exchange requires 240 ms to compute the call (call processing time).What is BHCA rating for the processor? If the exchange is capable of carrying 900E oftraffic, what is the CCR? Also calculate the GoS of the system. Assume call holding time of2 minutes.Explain different topologies of Data Communication Networks. Consider a group of 1200subscribers which generate 800 calls during the busy hour. The average holding time is 3.4minutes. What is the offered traffic in Erlangs, Cent call seconds (CCS) and calls minute(CM)?Q2.

We are authorized to answer one question at a time, since you have not mentioned which one you are…

A call processor in exchange requires 240 ms to compute the call (call processing time). What is BHCA rating for the processor? If the exchange is capable of carrying 900E of traffic, what is the CCR? Also calculate the GoS of the system. Assume call holding time of 2 minutes.

A call processor in exchange requires 240 ms to compute the call (call processing time). What is BHCA rating for the processor? If the exchange is capable of carrying 900E of traffic, what is the CCR? Also calculate the GoS of the system. Assume call holding time of 2 minutes.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

%00 |1. O Chapter #01_HW#.. -> Chapter #1 Programmable Logic Devices HW # 03 Q. Show how the PAL-type array in Figure below should be programmed to implement each of the following SOP expressions. Use an X to indicate connected link. A (a) Y = ABC + ĀBC + ABC (b) Y = ABC + ABC + ĀBC Electrical Engineering Departments University of Basrah •..
Using a combination of shift registers and latches explain how a small number ofmicrocontroller I/O pins can be used to read from or write to a large number of digitalsignal lines. Illustrate your answer. What is the main disadvantage of this I/O expansionapproach?
Q1: B- Fill out the following blanks: .3-The first 1- Bus-snooping is used for.......2- Two examples of status-flag registers.... computer that used 32-bit microprocessor was......... 4- The inter-processor communication via .5- If a system uses 16-bit address bus, it can reach memory locations up to.......6- Cache memory uses two algorithms for writing... 7- SRAM is better than DRAM due to.......
理 QA Qs Je Qe Qc JA QA le Qc 5 Volts KAQA KeQc Clock Figure (23): Example (14) Synchronous Counter. Synchronous Counter Design Modification H.W.: Design a MOD-5, 3-bit synchronous counter to count in the following sequence: 2, 3, 5, 1, 7. To modify the design and minimize the additional gates required for the J andK inputs, route the unused states to their next natural count state. In other words, route 0 to 1, 4 to 5, and 6 to 7. 2. A synchronous counter of n flip-flop stages always has a modulus of 2". A synchronous counter must count binary numbers in sequence, either up or REDMI NOTE 9 PRO ACQUAD CAMERA Section Self-Test 1. A synchronous counter has a common clock input to all flip-flop stages rof the questions).
q3mp plz provide answer for this question
1-Design a 3 – bit binary decoder (3 – to --8 decoder), 2-Design a BCD – to – Decimal decoder. 3- Design a Binary Number – tọ – 7-segment decoder."
I want the solution quickly, please
9. Compute the propagation delay and contamination delay of the following logic circuit. tcd = 2 ns tpd = 3 ns a b C d e tcd = 1 ns tpd = 2 ns m X tcd = 2 ns tpd = 3 ns y tcd = 3 ns tpd = 4 ns Z tcd= 2 ns. tpd = 3 ns
The terminal count up (TCu) and terminal count down (TCd) of 74193 are normally ____ . The TCu is used to indicate that ____ count is reached. HIGH, 9th B.LOW, 9th C. HIGH, 15th D. LOW, 15 E. LOW, maximumD. a BCD decade up/down counter E. a register