1- Using below given specifications of cement blends,a) Calculate the Bogue composition of each cement blend with the oxidecomposition given below.b) When you wish to remove the forms earlier, which one of the cement youcould choose and why ?c) Which one has higher resistence against Sulfate, and why?d) Which one is more suitable to use in mass concreting and why?|Compounds:СабSiO:Cement A(%66,6-0, 1n)(623,7+0,1n)%3,0%2,8% 1,0% 1,0% 1,93900Cement B(%61,0-0,1n)(%23,0+0,1n)%5,5% 6,5Cement C(160+0,In)g53,8g11,lg2,3g2.2g| 5,8g8,1g3200A120Fe;OMgOSO.OthersFineness (cm³/g)%0,5%1,0% 2,52800Bogue Formula:C3S = 4.071Ca0-7.6024SIO2-1.4297Fe203-6.7187A1203c2s = 8.6024SIO2+1.1Fe203+5.0683A1203-3.0710CaoC3A = 2.6504A1203-1.6920FE203C4AF = 3.0432Fe203

As per our guidelines, we solve three subparts .Kindly resubmit the question with remaining sub part…

a) Calculate the Bogue composition of each cement blend with the oxide composition given below. b) When you wish to remove the forms earlier, which one of the cement you could choose and why ? c) Which one has higher resistence against Sulfate, and why? d) Which one is more suitable to use in mass concreting and why?

a) Calculate the Bogue composition of each cement blend with the oxide composition given below. b) When you wish to remove the forms earlier, which one of the cement you could choose and why ? c) Which one has higher resistence against Sulfate, and why? d) Which one is more suitable to use in mass concreting and why?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Check whether the lime content for this type of cement is within acceptable limits if you know that the oxides are in the proportions Are as follows Calcium Oxide = 62% = Aluminum trioxide = 4% Sulfur trioxide = 2% Silicon dioxide = 18% Iron trioxide = 4%
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KN Solve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters. You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
This refers to a change from liquid state to solid state of cement paste.
I want the solution in less than 15 minutes
In a mortar mix ratio of 2:5.5, if the weight of fine aggregate is at 700 kilograms, then the weight of cement is
Calculate the chemical shrinkage (cm3/g) for one gram of completely hydrated Portland cement with the following compound compositions: C3S = 65%, C2S = 19%, C3A = 4%, C4AF = 9%
Most cement slurries will contain some additives to modify the properties of the slurry to produce a better cement job to suit particular requirements. Fluid loss additive helps to maintain constant water to solid ratio in cement slurry. Which of the following is advantage of fluid loss additive? a. Increase free water of cement slurries b. Maximize formation damage c. Changes in slurry rheology is seen d. Prevent stuck pipe
This is the type of Portland cement that is used when there is a need to produce the concrete strength within 2 to 3 days.
I want to solve this question quickly
a minor component that primarily contributes to total alkali content in portland cement is?
I need the answer as soon as possible
Please list primary chemical reactions during Cement Hydration