A byte-oriented (8bit/timeslot) TDMcommunication link with a bandwidth of300HZ – 4KHZ is used to connect 16terminals at one end of the link to 16computer ports at the distant end.If in this example each terminal is onlytransmitting data for 50% of the timedetermine if an STDM is more appropriatein this case (Assume the following forSTDM: 8-bit control field, 12-bit FCS field, 8-bit SYN and an address field comprised of asub-field of 4 bits to indicate number ofterminals transmitting plus one 4-bit sub-field for each terminal transmitting).

Answered: A byte-oriented (8bit/timeslot) TDM…

A byte-oriented (8bit/timeslot) TDM communication link with a bandwidth of 300HZ – 4KHZ is used to connect 16 terminals at one end of the link to 16 çomputer ports at the diştant end.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: Data communication Suppose that the spectrum of a channel is between 8 MHz and 10 MHz, and the…

A: In the realm of data communication, the efficient utilization of available bandwidth is crucial to…

Q: g communication types: Simplex, Half-Dupl

A: Step 1: Simplex mode is a one-way communication channel.Half duplex mode allows for two-way…

Q: Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During…

A: Given: TDM based circuit switching networks is transmits and receive signals on a single path by…

Q: Signals are demodulated in different ways using coherent and non-coherent psk demodulators.

A: Given: We have to discuss Signals are demodulated in different ways using coherent and…

Q: Wavelength division multiplexing is the term used for this in a nutshell.

A: The solution is given below for the above given question:

Q: Find the CDMA waveform for the following users ' data [1100 ] , [ 0101 ] , [ 1101 ] , [ 1000 ] and…

A: Required : CDMA waveform for given data and PG

Q: Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During…

A: Given that, Number of frames per second= 8000 Number of time slots per frame= 32 Number of bits…

Q: Multiplexing is done with TDM, FDM, and CDM on the physical layer. What are the pros and cons of…

A: Multiplexing is a technique used to transmit multiple signals over a single communication channel.…

Q: A certain number of data bits (D) are encoded by a single pulse in one of 2D possible positions…

A: Answer: c PPM

Q: Six channels, each with a 200 kHz bandwidth are to be multiplexed using FDM together. What is the…

A: It is an analog technique that can be applied when the bandwidth of a link (in hertz) is greater…

Q: The correct matching of the given table is A 3500 Hz signal 1 ELF B 250 Hz signal 2 VLF C 350 MHz…

A: Match the correct answers. Note: Kindly read the frequency range table mentioned in step 2, where…

Q: To improve the efficiency of a 32-Byte transmission line using (MUX/DEMUX) technique, the data will…

A: Multiplexing—shortened to "muxing"—is a method of transmitting and receiving information used by…

Q: A 5 kHz channel transmits a signal experiencing SNR of 31. What is the maximum Bit Rate of the…

A: It is used to determine the maximum bit rate of the channel given the bandwidth of the channel and…

Q: Computer science Describe the single mode in an optical fiber.

A: Introduction: single-mode in an optical fiber. A narrow diametral core in a single-mode fiber optic…

Q: How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link…

A: Introduction :Given ,Async. Mode of transmissionSize of char = 8 bits 9600 baud serial communication…

Q: How many bits per second can be sent over a communications system that has a baud rate of 4800 with…

A: The number of bits sent per second over a communications system with baud rate, B, and number of…

Q: Match the given baud rate and the number of bits carried by each signal unit (baud rate, bits) with…

A: 1) bit rate=baud rate x no of bits per signal =1200*3 =3600 (Answer 1) 2)…

Q: -A synchronous TDM with four 2 Mbps data stream inputs and one data stream output. The multiplexing…

A: Here we have given the answer for the first question as per the guideline.

Q: Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During…

A: Given, TDM-based circuit switching with 8000 frames per second 32 time slots per frame During each…

Q: you are using a connection with transmission rate of 64000 bps and a 3200 Km/s propagation speed,…

A: DATA GIVEN:- Data to carry = 1 bit Propagation speed =3200 km/s Distance = 1600 km TO FIND:- Total…

Q: Suppose a 128-kbps point-to-point link is set up between the Earth and a rover on Mars. The distance…

Q: The transmission of data makes use of both periodic analog signals and non-periodic digital signals;…

A: The explanation is provided in the section that follows.

Q: If data bits are transmitted serially at a 1 MHz rate, how many bits can be transmitted in 1 ms?

A: The data rate can be measured in terms of bits per second. It implies the number of bits transmitted…

Q: How many bytes of data can be transferred in 10 seconds via a serial link in asynchronous mode with…

A: iNTRO How many bytes of data can be transferred in 10 seconds via a serial link in asynchronous…

Q: The information density of QPSK, 8PSK and 8QAM modulation schemes with 8 Kbps data rate respectively…

A: In M-ary modulation, we can preserve bandwidth if we keep the symbol rate the same while increasing…

Q: A byte-oriented (8bit/timeslot) TDM communication link with a bandwidth of 300Hz – 4KHz is used to…

A: Time-division multiplexing (TDM) is a method of transmitting & receiving independent signals…

Q: The maximum data rate of a channel of 3000 Hz bandwidth and SNR of 30 db is

A: The correct answer is given below with an explanation and calculation

Q: Multiplexing is done at the physical layer using TDM, FDM, and CDM. What are the advantages and…

A: Multiplexing is done at the physical layer using TDM, FDM, and CDM. What are the advantages and…

Q: M-ary. Explain the

A: Disclaimer: As per guidelines, we can solve only one question at a time in multiple questions. Hence…

Q: UTP is color-coded according to(a) a 10-pair color code (b) a 25-pair color code(c) the resistor…

A: 10-pair color code is not enough to represent all colors of UTP cables Hence, the option (a) is…

Q: A DMA controller serves four receive-only telecommunication links (one per DMA channel) having a…

Q: 45. Consider the GPIB interface between a talker and a listener as shown in Figure 13-86(a). From…

A: Given:

Q: Describe the primary differences between synchronous and isochronous connections and offer an…

A: Introduction: Synchronous communication includes scheduled, real-time phone, video, or in-person…

Q: Q2/ A- Design TDM system to transmit the following 26 analog signals in to one channel and calculate…

A: The solution for the above given question is given below:

Q: Computer science What advantages does TDM have over FDM in a circuit-switched network?

A: Intro Time Division Multiplexing (TDM): Time-division multiplexing is a procedure of sending and…

Q: Computer science What is the maximum number of slots in a TDM frame if n signal sources with the…

A: Introduction: A method of transmitting and receiving separate signals across a shared signal route…

Q: Calculate the optical SNR at the output end of a 4000-km lightwave system designed using 50 EDFAs…

A: The ratio of the necessary information or power of an unwanted signal and the force of background…

Question

A byte-oriented (8bit/timeslot) TDM
communication link with a bandwidth of
300HZ – 4KHZ is used to connect 16
terminals at one end of the link to 16
computer ports at the distant end.
If in this example each terminal is only
transmitting data for 50% of the time
determine if an STDM is more appropriate
in this case (Assume the following for
STDM: 8-bit control field, 12-bit FCS field, 8-
bit SYN and an address field comprised of a
sub-field of 4 bits to indicate number of
terminals transmitting plus one 4-bit sub-
field for each terminal transmitting).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Distinguish between multilevel TDM, multiple slot TDM, and pulse- stuffed TDM.
Problem 3 A TDMA system provides 48.6 kbps data rate for a single user over one physical channel when 3 users are supported in a channel with 6 time slots in a frame. When the frame length is Tf = 40 ms, how many bits does one time slot contain?
Given a transmission rate of 1 Gbps and a propagation speed of 200m / μ sec , how many meters of cable are needed for a full duplex transmission link to have a minimum capacity of 1500 bytes?
The Fig 4.1 shows a demultiplexer of a TDM. If the frame size is 16 bits long (no synchronous / frame bits), what is the bit stream in each output? The bits arrive at the demultiplexer as shown by the arrow. 000011101010101010000111011100000111100011 Fig: 4.1
An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are carried by each signal element?
In synchronous TDM, it is possible to interleave hits, one bit from each channel participating in a cycle. If the channel is using a self-clocking code to assist synchronization, might this bit interleaving introduce problems because there is not a continuous stream of bits from one source?
What is the term used to describe the total of rotational delay and seek time?
Pulse code modulation is a method used by codes to transform an analog signal to a digital bit stream.
Let the Terminal count Register (TCR) content is (03FF)16 in the given DMA controller. In burst mode operation the maximum size of the data to be transferred is Kilo Bytes. (Approximately)
Explain the processes used in Time Division Multiplexing to handle varying input speeds.
Single tone signal frequency 3300hz a PCM is generated with a sampling rate of 8000 sample/sec. The required output signal to quantizing noise ratio is 30db What is the minimum number of uniform quantizing levels need and number of bit Calculate min. system bandwidth. Select one: a. 26,5, 30khz b. 1000,9, 40khz C. 26,5.20khz d. 1000,10, 40khz e. 128,7, 35khz