Bearing AIBearing IBChainage IDDD°Al'Al"DDD°IB'IB"СНCH153101017310101150(a) Briefly explain the main reason the used of transition curves, how the transitioncurve is used in road geometry design and the purpose of super-elevation incombine road curve design.(b) Two straights, Al and IB, whose bearings are DDD° Al A" and DDD° IB' IB"respectively intersect at point I, are to be connected by a combined curve. Thechainage of point / is CCCC m, while the design speed and radius have been fixedat 90 km/h and 550 m respectively. Adopting a rate of change of acceleration of0.3 m/s. As a civil engineer have been assign to do a trial analysis of the proposeddesign of horizontal combine curve (T1, T2, T3 and T4) and prepared road curvesetting-out data (T1 to T2, T2 to T3, T3 to T4) at 20 m intervals using deflection angleand chord distance method.(c) By adopting the coordinate of intersection point I as (YYYY N, XXXX E). Calculatethe coordinate of tangent point for T1, T2, T3 and T4.

a) Introduction : The following are the primary roles of transition curves (or easement curves): To…

Answered: (a) Briefly explain the main reason the…

(a) Briefly explain the main reason the used of transition curves, how the transition curve is used in road geometry design and the purpose of super-elevation in combine road curve design.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The intersecting angles (1) is most oftef measured at the radius point the midpoint of the curve…

A: Given data in question Intersecting angles To find out Where are the Intersecting angle measured

Q: When designing highways with curves, which is more advantageous, a degree of the curve that is…

Q: II. PROBLEMS 1) Module 12 - Horizontal Curves An existing highway with bearing of N20°E is to be…

Q: Given; A highway intersect a grade of (-)2.20 % to a (+) 3.80 %, this curve provides a 100 m…

Q: 2. A reserve curve has the following radius: R₁ = 380 by two tangents with an intersection equal to…

Q: Design of horizontal alignments depends on: Tangent distance (T) Friction on the road surface…

A: Design of horizontal alignment depends upon all of the above (1) tangent distance(T) (2) friction on…

Q: The tangent distance of a 3° simple curve is only ½ of its radius. a. Compute the angle of…

Q: A large grain elevator is located 40 feet from the centerline of a two-lane highway (55 mph…

A: Step 1:Step 2:

Q: and that the elevation of the intersection is 1010.69 feet. (a) What is the equation for the…

Q: With a radius of 280 meters and distance from Pc to Pt along the curve is 240 meters. - Compute…

A: Radius = 280mPC to PT distance = 240m

Q: The perpendicular distance between two parallel tangents is 10 m. If the angle of intersection of…

Q: A vertical curve on a roadway has a BVC at station 23+00 and an elevation of 900.00'. If the EVC is…

A: Given data: BVC station=23+00 EVC station=33+00 g1=4.00% g2=-3.50% Elev at station 29+00=?

Q: Discuss your point of view of the 3 kinds of horizontal curve, which is the easiest to analyze and…

A: Horizontal curve is provided for changing the alignment of road. Curves are generally provided when…

Q: The deflection angles of two intermediate points A and B of a highway curve are given below. The…

A: Highway Curve: Highway curve is the curve which is formed by connecting two straight lines on a…

Q: The highway shoulder is always contiguous with the travel lane to provide area along the highway for…

A: True

Q: tical curve is intended to connect grades of 1 45mph, determine the minimum length (ft) o to 3…

Q: In highway design, curves are deliberately provided even on a straight route to break the monotony…

A: Curves are provided to change the alignment and introduction of gradual alignment. But on straight…

Q: are the types of .….......... Vertical Curves Transition curves Simple and compound curves O Crest…

A: Answer:- Crest and sag curves Explaination:- Two types of the vertical curves are existed: They are…

Q: Briefly explain the main reason of using transition curves and how they are used in road geometry…

A: Given: Transition curves.

Q: n equal tangent vertical curve is intended to connect grades of 1.8% and -2.7%. If this curve is to…

A: From the given question it is required to calculate the minimum length of vertical curve part of a…

Q: The extra-widening required for off tracking due to rigidity of wheel base for a vehicle moving on…

A: Given - Speed of vehicle = 50 kmph Radius of curve, R = 360 m Length of vehicle, l = 6 m Number of…

Q: the radius of a horizontal curve on an existing highway is 250m.if the superelevation at the curve…

Q: The deflection angles of two intermediate points A and B of a highway curve are given below. The…

A: Given Chord distance (CAB) = 20 m Length of curve = 120 m

Q: Determine the minimum length (ft) for a vertical curve with 55mph design speed if the grades to be…

A: It is required to determine the algebraic difference in grade. A=G1-G2 Here G1 and G2 are the grade…

Q: An existing vertical curve on a highway with a 50 mph design speed joins a +2.7% grade with a -3.2%…

A: V=50 mph=80.47 kmphs=2.7%=0.027s=-3.2%=-0.032let us assume reaction time is 2 secondt=2sSSD=stopping…

Q: ual tangent vertical curve is intended to connect grades of -3.5% and 3.8%. If th speed limit of…

Q: True or False – Vertical Curve Design process is based on sight distance considerations.

A: Vertical curves design take sight dostance into consideration besides other factor

Q: In simple circular curve, the angle between fore tangent and back tangent is known as All of above…

A: Asked: Angle between fore tangent and back tangent in a simple curve is called

Q: Q.7 What is the length of transition curve for a BG circular curved track having a cant of 15 cm…

A: given- maximum speed vmax=90 kmphcant of track=15 cm

Q: when designing a highway curve is it required that cars at a constant speed of 33 m/s must not have…

Q: The radius of a horizontal curve can be determined based on the following criteria (select all that…

A: A horizontal curve in a highway refers to a curved section of roadway that allows for a change in…

Q: Civil Engineering Imagine a two lane highway segment with crown slopes of -1.3%and the start of the…

A: kbjjnoj nkokjpojpjpwjjwpj;k;kjlkjl kejlkejejnjrrhrheekkeje ejnelkknelkljelklene klknelnelkn…

Q: A spiral curve was laid out in a certain portion of Manila-Cavite coastal road. It has a length of…

A: Ls = 90m D = 40 I = 400

Q: A circular curve has 300 m radius and 60° deflection angle. What is its degree by (a) arc definition

A: Given - Radius, R = 300 m Deflection angle, ∆ = 60o To find - What is its degree by arc definition?

Q: A horizontal curve on a two-lane highway is designed with a 610-m radius, 3.5-m lanes, and 80 kph…

A: Given, R = 610 m w = 3.5 m V = 80 kph or 22.22 m/s f = 0.35

Q: QUESTION TWo The intersection angle of a 10° highway curve is 100°35' and the Point of Intersection…

A: Given data, Degree of curve D = 10o Intersection angle I = 100o35' = 100.583o Station of PI =…

Q: Determine the importance of utilizing an S-Curve in the field of Construction.

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: ertical curve is intended to conn f 50mph, determine the minim - to 3 decimal places.

Q: In simple circular curve, the angle between fore tangent and back tangent is known as All of above O…

A: To Determine :- The angle between fore tangent and back tangent in simple curve.

Q: Make a comparison for the curve used in rail roads and the curve used in roads and highways with…

A: Curves used in railway - Radius - The base railway bend radius is the briefest suitable plan…

Q: Problem 3: The angle of intersection of a simple curve is l=53.13 ° and the length of curve is…

Q: When a road is being built, it usually has straight sections, all with the same grade, that must be…

Q: An equal tangent vertical curve is intended to connect grades of 2.6% and -0.8%. If this curve is to…

A: Given Passing sight distance= 550 ft .

Q: how do you determine The highest possible design speed for the curve how do you assume whats correct…

A: The highest possible design speed for the curve: It is obtained by comparing the calculated middle…

Concept explainers

Curve setting

A curve is a turn that is provided horizontally or vertically in the design of highways, railways, and runways. A curve connects two straight lines that are separated by the deflection angle. It helps to change the direction and alignment of the highways, railway tracks, and runways. Therefore, the gradual change in their alignment is made by using a curve to provide comfort to the passengers and this also provides an easy turn to change the direction of the moving vehicle.

Question

Bearing AI
Bearing IB
Chainage I
DDD°
Al'
Al"
DDD°
IB'
IB"
СНCH
153
10
10
173
10
10
1150
(a) Briefly explain the main reason the used of transition curves, how the transition
curve is used in road geometry design and the purpose of super-elevation in
combine road curve design.
(b) Two straights, Al and IB, whose bearings are DDD° Al A" and DDD° IB' IB"
respectively intersect at point I, are to be connected by a combined curve. The
chainage of point / is CCCC m, while the design speed and radius have been fixed
at 90 km/h and 550 m respectively. Adopting a rate of change of acceleration of
0.3 m/s. As a civil engineer have been assign to do a trial analysis of the proposed
design of horizontal combine curve (T1, T2, T3 and T4) and prepared road curve
setting-out data (T1 to T2, T2 to T3, T3 to T4) at 20 m intervals using deflection angle
and chord distance method.
(c) By adopting the coordinate of intersection point I as (YYYY N, XXXX E). Calculate
the coordinate of tangent point for T1, T2, T3 and T4.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 a) Introduction

VIEW

Step 2 : a) Explanation

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Give me right solution urgent please
On a horizontal curve of a two-lane rural highway, the available sight distance is 250m. If the speed limit is 90kph, then is it necessary to mark the section as a passing zone? Also give suggestions to make this section of highway, geometrically economic.
Surveying Question on Curves
An equal tangent vertical curve is intended to connect grades of 4.2% and -3%. If this curve is to be a part of a highway designed with a speed limit of 60mph, determine the minimum length (ft) of the vertical curve. Use exact solution (do not use the table). Round your answer to 3 decimal places.
limit to 3 decimal places
Curve setting highways...
A two lane national highway having design speed of 50 kmph passing through a hilly terrain has a horizontal curve of radius equal to ruling minimum radius. Design all geometrical features of the curve. Calculate set back distance for SSD also.
Provide illustration and complete solution.
Why are circular curves used in urban residential areas instead of transition curves?
Clte advantages and disadvantages of LAYING-OUT A SIMPLE CURVE USING CHORD-DEFLECTION METHOD of LAYING-OUT A SIMPLE CURVE USING OFFSETS FROM Cite advantages and disadvantages TANGENTS
2) A tangent distance of a 4° simple curve is half (1/2) of its radius. Sketch and a) Compute the length of the curve (m) b) Compute the external distance (E) of the curve (m)
An equal tangent vertical curve is intended to connect grades of 0.9% and -2.7%. If this curve is to be a part of a highway designed with a speed limit of 50mph, determine the minimum length (ft) of the vertical curve. Use exact solution (do not use the table). Round your answer to 3 decimal places.