A boy stands out at the end of the diving board, which is supported bytwo springs A and B, each having a stiffness of k = 10 kN/m. The inposition shown the board is horizontal. If the boy has a mass of 55 kg,determine the angle of tilt which the board makes with the horizontalafter he jumps off. Neglect the weight of the board and assume it is rigid.- 3 mAB

Answered: Image /qna-images/answer/d31a19ea-341b-4764-9c3b-43875b81e2f3.jpg

A boy stands out at the end of the diving board, which is supported by wo springs A and B, each having a stiffness of k = 10 kN/m. The in position shown the board is horizontal. If the boy has a mass of 55 kg, letermine the angle of tilt which the board makes with the horizontal fter he jumps off. Neglect the weight of the board and assume it is rigid. – 3 m Fim- A B

A boy stands out at the end of the diving board, which is supported by wo springs A and B, each having a stiffness of k = 10 kN/m. The in position shown the board is horizontal. If the boy has a mass of 55 kg, letermine the angle of tilt which the board makes with the horizontal fter he jumps off. Neglect the weight of the board and assume it is rigid. – 3 m Fim- A B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Bi -3 m- 3 m The overhang beam above is supported by a pin at point A and a roller at point B. The beam is subjected to a uniform load with a magnitude of w = 15 kN/m. Which of the following is closest to the maximum magnitude of internal shear force (V) in the beam. O 90 kN 15 kN O45 kN 30 kN
The light right-angle boom which supports the 360-kg cylinder is supported by three cables and a ball-and-socket joint at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. A Ox - Answers: IM TAC = i Me C 0.65 m y 1.05 m! 0.65 m 10 B 360 kg 1.30 m 2.30 m N Oy E 1.45 m II D N TBD = 1.45 m Hr x N O₂ = Mi N TBE = i N N
Determine the stretch in each of the two springsrequired to hold the 20-kg crate in the equilibrium positionshown. Each spring has an unstretched length of 2 m and astiffness of k = 300 N/m.
3.75 نقطة )نقاط( السؤال 5 The beam is supported by a pin at A and a short link BC. If P = 5 kN and the diameter of the pin at C is 8 mm, determine the factor of safety against shear stress of pin .C assuming 800 MPa 2P |0.5,m 1 m-1.5 m -1.5 m- 4P 4P P. 0.5 m| 30 B 1.269 1.257 1.322 O 1.462 O
Lecture 2 A triangular roof frame consists of a horizontal tie rod and two rafters at inclined at 300 and 60⁰ respectively to the horizontal and is supported at the ends. It carries a load of 4 KN at the apex, determine the resulting thrusts in the rafters, the tension in the tie rod and the reaction at the supports. Using Lami's theorem N j at 30/ K X 4 KN raf 60
Problem 1 If roller support is added at point C, 20ft. from point A. Determine the following: (Use Conjugate Beam Method) 2 k/ft A B 30 ft El = constant E = 29,000 ksi | = 3,000 in. Required: 1. Reaction at A 2. Reaction at C 3. Moment at A
The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. Determine the maximum moment in kN-m. Given: w- 5 kN/m, W2 = 6 kN/m, a = 2 m, andb- 5 m. Neglect the mass of the beam. w2 kN/m w1 kN/m AAAAAAAA b m am A.
The small crane is mounted along the side of a pickup bed and facilitates the handling of heavy loads. When the boom elevation angle is 0 = 37°, the force in the hydraulic cylinder BC is 4.1 kN, and this force applied at point C is in the direction from B to C (the cylinder is in compression). Determine the moment of this 4.1-kN force about the boom pivot point O. The moment is positive if counterclockwise, negative if clockwise. 610 mm 105 mm 285 mm 345 mm B Answer: Mo = kN-m
(6) Determine the reactions at A and B for the beam subjected to the uniform load distribution. Draw the N,V,M diagrams. y I 4 kN/m L--x B 500 mm- A) A 400 mm-
STEEL DESIGN Situation 1: Situation 3: A light crane rail sits on and is securely fastened to a W crane girder. The girder is simply supported on a span of 6 m. The crane wheel loads are as follows: V = 80 kN and H = 8 kN. Assume full transfer of lateral load to the top flange of the girder. An 8-m long steel column is pinned at the top and fixed at the bottom. The column is provided with lateral support at mid-height in the weak direction. Properties: Ix = 178.1 x 10 mm4 Girder properties: ly = 18.8 x 106 mm4 A = 8129 mm²2 Weight = 67 kg/m Sx = 1, 280 x 10³ mm3 Sy = 361 x 103 mm3 7. Determine the critical slenderness ratio. a. 38 c. 27 Allowable stresses: b. 83 d. 41 Fbx = 164 MPa Find the critical buckling load. 9270 kN Fby = 186 MPa 8. 2190 kN 2310 kN a. с. Determine the actual bending stress about the x- axis. 1. b. 4730 kN d. Compute the minimum length of the column for which the Euler's formula is valid if the proportional limit of the steel used is 320 MPa. a. 99.12 MPa С. 93.75…
1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A and B. a. Draw the free-body diagram of the beam. b. What are the magnitudes of the reactions at A and B? G 45% A 14" F -1.2 m 1.5 mlm- B 30°
1. A frame held taut by a rope connected at D and E, is pin connected at B. If 1500 N is perpendicular to the member AB, determine the tension on the rope and the horizontal and vertical components of forces at B. Assume roller connection at A. 2000 N 2 m Fim--1 m- 1500 N 2 m 2 m 45° A