A box beam is constructed of four wood boards as shown in the figure part (a). The webs are h = 8 in.,t =1 in. and the flanges are b = 6 in., t = 1 in. boards (actual dimensions), joined screws for which the allowable load in shear is F = 280 Ib per screw. Flange Flange Web Web hi hi -- b - (а) (b) (a) Calculate the maximum permissible longitudinal spacing smax of the screws if the shear force V is 1,200 lb. Round your answer to two decimal places. Smax 5.08 in. (b) Repeat (a) if the flanges are attached to the webs using a horizontal arrangement of screws as shown in the figure part (b). Round your answer to two decimal places. Smax = 4.63 O in.

A box beam is constructed of four wood boards as shown in the figure part (a). The webs are h = 8 in.,t =1 in. and the flanges are b = 6 in., t = 1 in. boards (actual dimensions), joined screws for which the allowable load in shear is F = 280 Ib per screw. Flange Flange Web Web hi hi -- b - (а) (b) (a) Calculate the maximum permissible longitudinal spacing smax of the screws if the shear force V is 1,200 lb. Round your answer to two decimal places. Smax 5.08 in. (b) Repeat (a) if the flanges are attached to the webs using a horizontal arrangement of screws as shown in the figure part (b). Round your answer to two decimal places. Smax = 4.63 O in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force acting on members DE, DC, BC in an inverted roof truss as shown below. Use method of sections in solving. G 21' E F 30 kips 21' C 30 kips D 21' B LA -21- -21- 7--7'--7' 30 kips
Calculate the forces in all members of the truss shown, using method of joints. B C 10 kips E F 5 kips 7 kips 3 bays@18'-0"=54'-0" 16' 0"
In a truss girder of a bridge, a diagonal consists of mild steel flat 400 ISF and carries a pull of 80 tonnes. If the gross diameter of the rivet is 26 mm, the number of rivets required in the splice is.
Solve the truss below and identify if the various members are in Tension and Compression, along with their forces. Solve both questions please.
A beam is composed of the following cross-section and carries a maximum shear of 4000lb. Find the force in all four nails assuming a spacing of 1.5”. Show all process steps please
Please answer in 20 mins
I need help solving this exercise, and please also explain method of sections:Determine the force in members EF, EP, and LK of the Baltimore bridge truss and state if the members are in tension or compression. Use the method of sections. Also, indicate all zero-force members.
Find all member forces and state whether tension or compression (Hand written please )
20 kN- 20 kN- A F G H C 80 kN 4 at 3 m 12 m- D 60 kN E Determine the force in each member of the truss using the METHOD OF SECTIONS. State whether the force is in tension (T) or compression (C). Please include all the FBDs and complete the solution in a clear manner.
ASAP!!! NEED RIGHT COMPLETE SOLUTION !!!
Determine the force in each member of the truss shown. State whether each member is intension or compression. Use the method of sections. Please find all the forces in each member. Thank you!
ㅏ 2m 2P 2m B Im 4cm 8cm 4cm 4cm 12cm 4cm An overhanging beam is constructed by four wood plates with rectangular cross-section by nails as shown in the figure. If the allowable stresses are oo-10 MPa and t-1 MPa: a) Determine the load P that the beam can carry safely. b) If each nail can support a shear force of Q=2 kN, determine the required nail spacing e using the load P calculated in question (a).