A box beam is constructed of four wood boards as shown in the figure part (a). The webs are h = 7 in., t = 1 in. and the flanges are b= 4 in., t = 1 in. boards (actual dimensions), joined by screws for which the allowable load in shear is F = 300 lb per screw. Flange Flange Web T Web (a) (b) (a) Calculate the maximum permissible longitudinal spacing smax Oof the screws if the shear force V is 1,300 lb. Round your answer to two decimal places. Smax = in. (b) Repeat (a) if the flanges are attached to the webs using a horizontal arrangement of screws as shown in the figure part (b). Round your answer to two decimal places. Smax = in.

A box beam is constructed of four wood boards as shown in the figure part (a). The webs are h = 7 in., t = 1 in. and the flanges are b= 4 in., t = 1 in. boards (actual dimensions), joined by screws for which the allowable load in shear is F = 300 lb per screw. Flange Flange Web T Web (a) (b) (a) Calculate the maximum permissible longitudinal spacing smax Oof the screws if the shear force V is 1,300 lb. Round your answer to two decimal places. Smax = in. (b) Repeat (a) if the flanges are attached to the webs using a horizontal arrangement of screws as shown in the figure part (b). Round your answer to two decimal places. Smax = in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) The short steel post as shown in Figure 4 is a 152 x 152 UC37 with three compressive loads applied to the top. There is a central load of 200KN and eccentric loads of 'W kN and 100kN. The maximum allowable stress on the face AB is 185 N/mm?. (Area=D47.1cm2,Zxx=273cm) What is the value of the load 'W in kN? WkN A. 152 x 152 UC37 100mm -200KN 50mm 100KN Not to scale Figure 4
ure B 2m2 m C -2 m D 4 m 500 N 700 N 2 of 2 Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. 000 CD DE CG CF FG BC BG DF AG EF AB Submit Provide Feedback Request Answer
A stud wall panel has an overall height of 4m including top and bottom rails and vertical studs at 400 centres with nogging at mid- height. Assuming that the studs, rail framing and nogging pieces comprise 47 x 125mm section of C24 strength class, calculate the maximum uniformly distributed medium term load the panel is able to support. Use service class condition 2. λιγ = ixx = Scadm.ll (N/mm2) = Choose... • Choose... Choose.... The uniformly distributed load capacity kN/m Choose.... Axxx = K12= Emin/8cl= Choose... • Choose... Choose.... iyy= Choose....
T L 3. The wooden bar consists of two segments, each of length L. one segment has a square cross section of width d; the cross section of the other segment is a circle of diameter d. The working stress for the wood is 5MPa and he shear modulus is G = 0.5GPA. Using L = 0.6m and d = 50mm, determine the largest torque T that can be safely applied and the corresponding angle of twist for the bar. (Practice at Home)
In a truss girder of a bridge, a diagonal consists of mild steel flat 400 ISF and carries a pull of 80 tonnes. If the gross diameter of the rivet is 26 mm, the number of rivets required in the splice is.
Hand written and clean solution please
2. Calculate the internal forces in the bar GF and GD in a roof truss as shownbelow. For each bar, indicate if the internal force is tensile or compressive. Usethe section method (snittmetoden). Point A has simple support and D has rollersupport.
answer asap pls, thank you
Draw the shear diagram for the following beam
20 kN- 20 kN- A F G H C 80 kN 4 at 3 m 12 m- D 60 kN E Determine the force in each member of the truss using the METHOD OF SECTIONS. State whether the force is in tension (T) or compression (C). Please include all the FBDs and complete the solution in a clear manner.
2 - please provide a clear and complete solution, thanks!
NEED REALLY FAST