A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on the cross-section is 12 kN-m, determine the flexural stress in MPa at point AWhere:tw = 22 mm; and d = 293 mm A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on thecross-section is 12 kN-m, determine the flexural stress in MPa at point AWhere:tw = 22 mm; and d = 293 mmtw160 mmtw25 mmd.25 mmMoment (m)

To find out the flexural stress in Mpa for point A.

A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on the cross-section is 12 kN-m, determine the flexural stress in MPa at point A Where: tw = 22 mm; and d = 293 mm tw 160 mm tw 25 mm d. 25 mm Moment (m)

A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on the cross-section is 12 kN-m, determine the flexural stress in MPa at point A Where: tw = 22 mm; and d = 293 mm tw 160 mm tw 25 mm d. 25 mm Moment (m)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa. F 2.0 m E P = 30 kN 2.5 m D -3 m- -3 m-
Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F = 4.6 kN, a = 4.0 m, b = 3 m, c = 2 m, and d = 2 m. A F Answers: BE= BD = a i i B b E a b D с d KN KN
If the allowable bearing stress for the material under the supports at A and B is = 710 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10ft, and b = 5 ft. Answer: Pmax i a B b lb
A simply supported wood beam that is 13.2 m long carries a 41 kN concentrated load at B. The cross-sectional dimensions of the bearn are b = 125 mm, d = 350 mm, a = 110 mm, and c= 35 mm. Section a-a is located at x= 2.2 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entirespan. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P. a H a a B C K 2L 3 3 Answer: (a) TH = i 689 КРа (b) TK = i КРа 280 (c) Tmax= i 799 kPa (d) Omax= 47.11 MPa
a=7m b=2m c=5m 2 3rd QUESTION Determine the reaction forces force of the loaded truss. 45° 10 kN C b B a
A simply supported wood beam that is 9.3 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 400 mm, a = 80 mm, and c = 30 mm. Section a-a is located at x = 1.6 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. a Н to A a В K 2L 3 3 Answer: kPa (a) TH = i kPa (b) TK = i kPa (c) Tmax = i MPa (d) Omax = i
Design the beam using the Working stress diagram to resist the loads. Take fc = 10 MPa, fs = 120 MPa, n = 12, bar diameter = 20 mm. Take b = d/2.
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression. Α' 28 kips Answers: BC = i B 12' G CG = i 11' 12' C 12' D F 66° E kips kips
A simply supported wood beam that is 14.1 m long carries a 47 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 360 mm, a = 70 mm, andc = 20 mm. Section a-a is located at x = 2.4 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. y H a a A В K L 2L Answer: (a) TH = i kPa (b) TK = i КРа (c) Tmax = i kPa (d) Omax MPa i 13
3
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m