A) Both are one-way roads (B) Both are two-way roads (C) One is two-way road and other is one-way road (D) None of these Road makers along roads from the edge of a kerb should not be less than (A) 40 cm (B) 45 cm (C) 50 cm (D) 60 cm true

A) Both are one-way roads (B) Both are two-way roads (C) One is two-way road and other is one-way road (D) None of these Road makers along roads from the edge of a kerb should not be less than (A) 40 cm (B) 45 cm (C) 50 cm (D) 60 cm true

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: determine the adequacy of the intersection sight distance provided that will ensure that vehicle ‘A’…

A: The safe line of sight distance is calculated based on sight triangle. Stopping distance on minor…

Q: you are a Highway Engineer and you have to design a road with a horizontal curve, how much…

A: Given Data: Radius of the curve is R=40 m. Design speed for the road is V=60 kmph

Q: The crossing of traffic streams moving the same general direction accomplished by merging and…

A: Given data in question Traffic streams Merging and diverging To find out Accomplished merging and…

Q: b) As a Traffic Engineer, do you think there are enDIS with regards to the road signs and markings…

A: As traffic engineers, they have to conducts capacity analyses to determine how much traffic can…

Q: Which of the following is not a type of freeway section? Basic freeway segment 000 Diverge segment…

A: As part of highway infrastructure, freeways play a crucial role in facilitating efficient and rapid…

Q: 1)Define flash point and fire point? 2)What are the applications of flash and fire point test?…

A: Solution: 1) Define flash point and fire point Flash point is basically the lowest temperature at…

Q: A two-lane highway along the border has a horizontal curve segment with radius of 656 ft (measured…

Q: Q5/ A- A highway section, +2% , meet -8%at point with 52.0 m at speed 110 Km/hr. Determine the…

A: Introduction : Horizontal Curves are the first of two major transition features in highway geometric…

Q: What super-elevation rate would you recommend for a roadway with a design speed of 110 kph and a…

A: given data: f=0.11 V=110 kph radius (R)=1400 ft

Q: Superelevation is developed over a given length of roadway, beginning with a road to being fully…

A: This question is related to the Highway Engineering and Traffic Engineering.

Q: RING 1 RING 2 $1 2 DJL $5 MAJOR STREET lead-lag lag-lag none $2 $6 BARRIER = Phase Number =…

A: Protected permitted operations are a combination of the permitted and protected modes. Left-turning…

Q: In relation to our lecture(Intersection Control), show how the Phillippines applied this principles…

Q: You are asked to: A. Determine the maximum peak-hour volume that the segment can serve at a LOS C.…

A: Given data: Lane width=3.4 m Number of lanes(N)=2 in each direction Lateral Clearance=3m 85%…

Q: passing and no passing sections

A: Passing sections of a highway refers to the zone of road where overtaking a slow moving vehicle is…

Q: A six lane highway (three 12-ft lanes in cach direction) has a superelevation of 6%, and a design…

Q: 2 A vehicle initially traveling at (75 mile/hr.), skids to a stop taking (170) m to do so. the…

A: Stopping sight distance is the length on highway which is sufficient for stopping a vehicle…

Q: Determine if a segment of 700 feet is safe for vehicles to decide to maneuver on a two-lane rural…

A: To determine if a segment of 700 feet is safe for vehicles to maneuver on a two-lane rural highway…

Q: QUESTION 6 ONIN $1 $5 MAJOR STREET 42 O none DL 46 BARRIER -Phase Number - Protected Movement MINOR…

A: The Lead-Lead sequence, in which the two opposing Left-turn phases begin at the same moment, is the…

Q: 1. According to its functions, the highways classified in to 2. Highway location process involves…

A: 1. According to its functions, the highways classified in to three classes. They are arterial,…

Q: An antique 6-lane urban parkway has the subsequent characteristics: 11-ft lanes; common roadside…

Q: Design a highway with the following criteria (Determine the minimum radius, widening and check if it…

Q: If a four legged roundabout has 8 conflict points, how many does a 3 legged roundabout?

A: Roundabout is circular intersection which allows slow and safe traffic flow around the central…

Q: Exit 63 of I-90 includes a tight loop ramp with a radius 250 ft. The advisory exit speed is 30 mph.…

A: Solution: Given: Radius: R=250ft Speed V=30mph As per AASHTO DESIGN MANUAL FOR ALIGNMENTS: For…

Q: A rural collector highway located in mountainous terrain is designed to carry a design volume of…

A: Given, This question Is related to Highway & Transportation Engineering. Our aim is to answer…

Q: (b) As a civil engineer, you are involved in highway road constructions. Discuss the purpose of…

A: - Transition curve can be defined as a curve where straight road with horizontal alignment is change…

Q: A direct factor that directly affects the required right of way necessary to construct the road.

A: Before knowing the factor firstly we should know the Definition of Right of Way or What is Right Of…

Q: A 6 lane highway (3 lanes in each direction) has 11 ft wide lanes, 8 ft wide shoulders, 50 degree…

A: Given, Design speed = 60 mph Central deflection = 65o

Q: 4. A diversion sign is located 230ft to the diversion point on a 3% down hill road. The road sign…

A: Distance between the diversion point and the diversion sign = 230ftThe slope of the hill road, n =…

Q: HW2: OFFS on Multilane Highway O Four lane undivided multilane highway O Posted speed limit-D50mi/hr…

A: Given data- 4 Lane undivided highway. Posted speed limit = 50 mph Lane width = 11 ft Right shoulder…

Q: . Which of the following are the accepted criteria for design of valley curve for highways? 1.…

A: Valley curve are the vertical curves with Convexity downward. Valley curve are formed when 2…

Q: are there to distribute e and fs? What is different about

A: Different methods are - 1. : e +fs=V2127R 2. : e + fs = V2225 R 3. : 0.01e + f = V215…

Q: A two-lane major road with 40 mph east west direction crosses a two-lane minor road with 30 mph at a…

Q: What are the major reasons for accidents at curved highway?

A: Accident Reasons on Curved Highway-

Q: What is the first area of the temporary traffic control zone? Maintenance Area Advanced Warning Area…

Q: A T-intersection is the meeting point of a two-lane minor road (one lane in each direction) with a…

A: Conflict points can be defined as the potential points where there are chances of colliding with the…

Q: The 2 eastbound lanes of a rural divided highway have 13 ft lane widths. There is no lateral…

A: Answer We know that the Free flow speed(FFS) for multilane highway is computed using FFS = BFFS -…

Q: ive way sign is an effective control technique at the intersection of two arterial roads with…

A: In order to determine the most appropriate control measures for a specific intersection, traffic…

Q: How can we tell what the effect is likely to be without building the freeway?

A: Freeway, highway, or corridor is a long length of road that connects various small or large roads at…

Q: SIT: A highway curve has the ff. technical description: Radius of central curve = 300m Length…

Q: |-90 crosses the Snoqualmie River at about milepost 47.5. Here, the eastbound portion of the…

A: Given: Rural freeway having following characteristics No HOV lanes 12 ft lane width, 10 ft right…

Q: The radius of a horizontal curve on an existing highway is 230 m. The superelevation rate at the…

A: - Speed limit on road, V = 100 km/h (1) Maximum speed on horizontal curve can be determined using…

Q: What is the calculated stopping sight distance (ft) for a -3% grade when the design speed is 55 mph,…

Q: QUESTION 2 طار How many diverging conflicts are present at a 4-leg intersection where each leg is a…

A: The 4-leg intersection where each leg is a single lane approach has 4 diverging conflicts.

Question

At a road junction, 16 cross conflict points are severe, if

(A) Both are one-way roads

(B) Both are two-way roads

(D) None of these

Road makers along roads from the edge of a kerb should not be less than

(A) 40 cm

(B) 45 cm

(D) 60 cm true

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A vehicle hit a big tree near the edge of highway pavement. Based on the conditions of damages on the vehicle, the estimated speed when the vehicle hit the tree was 20 mile/hr. The observed skid mark on the pavement was 350 ft. The grade of the highway is 3% downward and F=0.35. What is the initial speed of the vehicle right before the driver pushed the brake ?
Ramps should be placed at intervals that will not cause confusion or increase the crash potential on the freeway or expressway true or false?
During peak periods, “Trotro” drivers use the shoulders as travel lanes on the section of the Kasoa road approaching the toll booth from the West Hills Mall direction. As a Highway Engineer, what design intervention would you propose to prevent the shoulders from being used as travel lanes during congested period or as part-time shoulders but still function as shoulders? (CR,5)
7. what would the DHV of the road be if the AADT were 40,000 vpd and assume a D of .65 and How many lanes would you out on this road if the design speed was 50 mph
Choosing the best highway routes depends on: Follow of attaining ruling gradient Avoidance of cutting hard rocks Minimum number of bridges All the above
designing a rural highway is required so how many lanes are needed in the peak hour based on the given information:v = 4000 vehicle/ hour (per lane )level terrainPt ( trucks ) = 15%Pr = 3%Fp =1lane width 3.6mlateral clearance 1.8mphf =0.85interchange density = 0.9 interchange/km..no LOS was given and the units (metric)
How many diverging conflicts are present at a 4-leg intersection where each leg is a single lane approach, as shown above? Response Feedback: NBTH with NBLT, NBTH with NBRT EBTH with EBLT, EBTH with EBRT SBTH with SBLT, SBTH with SBRT WBTH with WBLT, WBTH with WBRT
Two low-volume two-lane streets (lane width = 11 ft) intersect in an urban residential area at 120-60 degree-angle. Recommend appropriate curb configurations for this intersection based on AASHTO (2011) recommendations for a passenger car design vehicle. Draw a neat sketch for the intersection showing the dimensions of all elements you selected in your design.
How many numbers of conflict are present in a 4-legged intersection? a.12 b.8 c.4 d.6
Problem 5-11 in in Roess, Prassas, McShane, 5th ed. A study of speed-flow-density relationships at a particular freeway site has resulted in the k following calibrated relationship: u = 71.2 (1 - 1/2) 122, a. Determine the free-flow speed for the relationship. b. Determine the jam density for the relationship. c. Derive the equation for speed versus flow for this site. d. Derive the equation for flow versus density for this site. e. Determine the capacity of the segment mathematically.
An important feature of roadside design improves a driver’s ability to control and recover their errant vehicle.
6. A subdivision road is entering a public road. There is a stop sign before entering the public road. The reaction time is 2.5 seconds. The friction factor is 0.3. What the triangle dimensions that will define the clear sight triangle easement. Grade Speed % mph 3.0 20 Subom Rd 2. 3.5 25 3 4.0 40 4 4.5 30 1.0 35 2.0 40 7. 1.5 35 8. 2.5 55 9. 3.0 20 10 3.5 40 11 1.0 30 12 1.5 35 13 3.0 40 14 2.5 30 m2.