A Boolean function using the three variables function, given by F(A,B,C) = ac' + a'c is implemented using a 3x8 decoder. The pins connected to the OR gate that outputs %3D F(A,B,C) are -- a. 1, 3, 4 and 6 b. 0, 2, 4 and 7 O c. 3, 4, 5 and 6 O d. 1, 2, 4 and 5

A Boolean function using the three variables function, given by F(A,B,C) = ac' + a'c is implemented using a 3x8 decoder. The pins connected to the OR gate that outputs %3D F(A,B,C) are -- a. 1, 3, 4 and 6 b. 0, 2, 4 and 7 O c. 3, 4, 5 and 6 O d. 1, 2, 4 and 5

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

parity generator design, construct and test a circuit that generates an even parity bit ffrom four messages bits . use XOR gates. adding one more XOR gate, expand the circuit so that it generates an odd parity bit also.
Q3/ Design binary adder that add three BCD numbers (1-digit) using CPAS. Q4/ Design a counter which count in the following sequence 0, 2, 4, 6, 8, 10, 12, 14 using T- F.F.
An equation in reduced SOP form, is F=AB+B'C+A'C'. I need to draw a logic circuit F using NOT/AND/OR and logoc circuit F using all NAND gates. Thank you for the help. I understood the previous types of gates but I am confused on how to draw these circuits.
Write a VHDL program to implement a 2-bit adder. The Boolean functions for the 1-bit full adder are given in the diagram:
Q2. The sum of products for a 5 input variable function is given below f = =Σm(0,2,5,8,10,13,16,18,19,20,21,22,24,26,28,30)
1. Implement the following Boolean function by using 4x1 multiplexer. F(A,B, C, D) = Em(1,3,5,6,8,11,14) 2. Construct a logical circuit of 64 x 1 multiplexer using 4 × 1 multiplexer. 3. Construct a priority encoder circuit of 8x3. 4. Design a 4-bit BCD to Gray Code Converter by using Programmable Array logic.
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate thecomplete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform.(Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.)(Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)
1. What is the modulo of the circuit below? 2. Make a table of the count sequence. 3. A BCD counter can assume____discrete state. 4. A BCD counter can divide its input frequency by____. 5. A four-bit binary counter contains the number 0100. Nine inpulse occur. The new counter state is_____. 6. Design a 4-bit down counter.
Design A one bit, 3 input majority counter (voter) explain how it works in simple steps. include in the truth table of the circuit and also need to use the Boolean Algebra/Karnaugh Map to minimize the number of gates used in the design and build of such circuits.
i need the answer quickly
Given the positive number 77. a) Represent the number as an eight–bit number in two’s–complement form. Also give the 2 character hexadecimal value. b) Represent the negative number –77 as an eight–bit number in two’s–complement form. Also give the 2 character hexadecimal value. c) Add the binary result for a to b to verify you get an eight-bit value of zero!
Grey converters are often used in industrial circuits where the normal sequence of binary numbers may produce ambiguity during transition. This is elliminated with the Grey code, as only one bit changes, during a normal transition of sequential numbers. Show the logic required to convert a 10-bit binary number to Gray code and use that logic to convert the following to Gray code: a) 1010101010 b) 1111100000 c) 0000001110 d) 1111111111