A bolt on a polyethylene reactor must be able to withstand a minimum force of 220 kN, not including any safety factors. If the bolt is 25 mm in diameter what material you would use: 1040 steel (normalized), 316 steel (annealed) or 1095 carbon steel quenched and tempered. Which would you select. Justify your material selection. Show all work

Q: Cp = Cv + R Prove??

A: Cp=Cv+R

Q: Which of the following tools is used in both marking and measuring? O Center Punch O Mallet O None…

A: Center punch is a marking tool used to mark center of a hole which is to be drilled. It is not a…

Q: What type of scale is 1:20? O Full Scale O Enlargement Scale O Reduction Scale O O O

A:

Q: The product from an open - circuit primary rod mill receiving 160 tons/hour of new ore feed joins…

A: Given:Rod mill product stream:  solids by weight.Ball mill product stream:  solids by…

Q: Don't Use Chat GPT Will Upvote

A: Diagram-    Detailed Explanation of Reflection on a Curved Surface Understanding Key Concepts:1.…

Q: In the TRIM command, when selecting objects to trim, holding downthe <Shift> key: a. Allows…

A: By holding the <Shift> key while using the TRIM command, it will be inverted to the opposite…

Q: A composite beam is fabricated by bolting two 2.3-in.-wide by 14-in.-deep timber planks to the sides…

A:

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: Name the feature shown below. 10 00

A: the feature displayed in the picture is extrude

Q: OFFSET command use to draw object parallel to selected object by determine radius distance point…

A: Computer-aided drawing is the way to draw the various views of the component. In the orthogonal…

Q: Pls provide the sectional view below

A:

Q: I need 3 d figure ASAP make anything u know I need it urgent fast fast

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: raw the sectional view

A: According to the details provided in the question, we need to draw a sectional view according to the…

Q: Draw front, top and then left side view.

A:

Q: Stoker

A:

Q: In milling machine axis controls the spindle movement in the upward direction. a. Negative Y b.…

A: Milling Machine: Milling is a multi point cutting tool machining operation used for removing a layer…

Q: The part view should.com RANCES be the same CHD APPVD MIG GA as picture. 2- The color is RGB as DWG…

A: Find Draw the given object using the drawing.

Q: OA F >F>F OE- F = F, F, >F, >F, F > F, >F, D) OF> F >F,

A: Forces on the surfaces, F1,F2,F3 Area of each surfaces, 2S,S,3S

Q: Q4 After losing a race championship with few points, a constructor was eager to boost their vehicle…

A: In IC engines a carburetor's function is to air and fuel to supply to the engine. Its primary…

Q: 14 sketch in the missing object and ce nter lines on 14

A: Given figure  To sketch the missing lines  And hidden lines

Q: DRAW THE MULTIPLE VIEW

A: The given view is in isometric view

Q: if Re 77 Soo %3D 등 = \ , * 103 Determine f %3D from mod'] chart.

A:

Q: The part view should be the same as picture. 2- The color is RGB as 0,220,100. 3- Should use the…

A: Find Draw the given object using the drawing.

Q: What does SPC stand for?

A: SPC stands for statistical process control, which is the application of statistical instruments and…

Q: Divider tool is used for marking arcs in marking layout activity Select one

A: Divider is a tool with two point sharp metal points.

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Q: The following was recorded from the chiller at the BYU-Idaho Central Energy Facility. Atmospheric…

A:

Q: UNITS: INCHES MATERIAL: ALUMINIUM -R.75 0.3 4.00 4.00 3.5 0.3 2.0 0.3 0.75 0.75 2.3

A:

Q: 1. FRONT AND TOP VIEWS ARE COMPLETE. SKETCH AUXILIARY VIEW OFF FRONT VIEW. NOTE: SHOW HIDDEN LINES…

A: Given  1 . Front and top is given  To sketch the auxiliary view

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: Draw the multiple view

A: Given isometric view

Q: hello did you forgot the T in solving Wrev?

A:

Q: Name the feature shown below.

A: The given figure is of

Q: A00007: Drafting Competencies - To create drawing view B' it is necessary to select drawing view 'A'…

A: Break view in the solidworks is used to display the larger drwaing in smaller drawing sheet by…

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: -30- R-64 20 -10 (5.0) -50 -40 -30 -20 -10 10 10-

A: given:

Q: How did you get the Tsat values

A: This question is based on the properties of water at different temperatures and pressure.

Q: A saw its angular velocity when work is 1500rpm when its stopes by magantic brake it needs 1 min to…

A:

Q: ers O way of telng ems the following practical tests end C plus collect data. al investigation and…

A: Hi and thank you for the questions. Since you have asked multiple questions, as per our honour code…