A Boeing 777-200 commercial jet weighs, fully loaded, 325,000 kg. The pilot places the turbines in maximum power condition for takeoff (before releasing the aircraft's brakes), situation in which they generate 450 kN of thrust in each turbine. Neglecting aerodynamic and bearing, estimate runway length and time necessary to achieve the speed of takeoff of 225 km / h. consider constant thrust in the two turbines during the journey on the ground.

Q: A flat belt is required to transmit 28 kW from a pulley of 1.3 m effective diameter running at 300…

A:

Q: A fan is to be used as a levitation demonstration. The air blows through the box-enclosed fan of 3…

A: according to the given information weight of the fan is  69lbf, height is 3 ft. The formula for…

Q: The thrust generated by a single jet engine a for s F=59000n. It take the plane (with a mass of…

A: Given: m = 6300 kg k = 100000 N/m F = 59000 N s = 0.95 km

Q: What horsepower is required to isothermally compress 755 cu.ft. Of air per minute from 14.7 psia to…

A:

Q: For a maximum temperature of 1650 and 1800 K at pressure ratios in the compressor of 12, 15, 20 and…

A: Given that- Maximum temperature = 1650 and 1800 K Pressure ratios = 12, 15, 20 and 25:1

Q: A wind turbine located at a height of 25m from ground, produces 950 kW. Its hub diameter negligible…

A: Assumption 1) Density of air is 1.2 kg/m3 2) Length of blade and radius of rotation is equal 3)…

Q: In the 1950’s an experimental train that had a mass of 25,000 kg was powered across a level 500 m…

A:

Q: Show that the force exerted by a liquid jet on a stationary nozzle as it leaves with a velocity V is…

A: Assumptions: Flow is steady and incompressible. The frictional effects are negligible. Flow is…

Q: Sam, whose mass is 68 kg , straps on his skis and starts down a 68 m -high, 20∘ frictionless slope.…

A:

Q: Consider a turbojet-powered aircraft flying with a airspeed of 250 mi/h at an altitude of 20,000 ft.…

A: Given data: Airspeed = u  = 250 mi/hr = 111.76 m/sAltitude = 20000 ft Inlet Area = 15 ft2 = 1.3935…

Q: The average wind speed in a proposed wind farm with a horizontal axis wind turbine (HEWT) is 16.2…

A: Given data as per question The average wind speed = 16.2 m/s Power coefficient = 0.462  Gearbox and…

Q: Determine the maximum power a wind turbine may produce at the following wind speeds: 1, 5 and 10…

A: Introduction Wind power plants use a number of wind turbines positioned together to generate energy.…

Q: If velocity of entering air and jel are 150 m/ s and 350 m/s, the thrust power will be equal to…

A:

Q: (a) Find the useful power output of an e load a height of 450 cm in 12.0 s, if it al 5.00 m/s. Note…

A: Write the work-energy theorem as follows.

Q: Explain the concept of the effect of i. Shifting a mass within a body ii. Adding a mass to a body…

A: As per policy i have solved first 3 for you.   Explain the concept of the effect of-  Shifting a…

Q: A spacecraft has a monopropellant propulsion system that delivers an Isp of 225 s. How much…

A:

Q: ssuming the there are no heat effect and no frictional effects, find the kinetic energy in BTU of a…

A: To find the kinetic energy in BTU.

Q: jet fighter is flying at M = 3 at a height of 30,000 ft. A diffuser at its engine entrance reduces…

A:

Q: ㅁ T

A: Given: Mass of the bucket→m=150 g=0.15 Kg Mass flow rate of the water deposits →m'=63.1 g/s=0.0631…

Q: The diameter of jet of a turbojet is 2.5 m and it flies at 500 km/h at an elevation of 8 km for…

A: Given Data : Diameter of Jet dj = 2.5 m speed u= 500 km/h = 138.89 m/s Elevation z = 8 Km = 8000m…

Q: jet

A: Let vane is symmetrical then; θ0=θ1=θ 180-2θ=150θ=15o…

Q: A jet engine is bolted to a stationary test stand and run at full thrust. Air enters the engine at a…

A: Force required to hold the engine in place on the test stand=thrust Produced by the jet engineForce…

Q: PROBLEM 8. The total weight of space shuttle including its payload mass and the empty external tank,…

A: Given data The total weight of space  mo = 428,100 lb. The external tank and the two solid rocket…

Q: 2. A fluid undergoes a frictionless process in a closed system from V₁ = 5ft' to V2 = 2 ft³ in…

A:

Q: I need handwritten otherwise I'll dislike A two-bladed horizontal axis wind generator has a 30 m…

A:

Q: A bus of mass 800 kg is travelling witha speed of 8 m/s. What will be the momentum of the bus.

A: Given data: -  The mass of the bus is M = 800 kg. The speed of the bus is v = 8 m/s.

Q: A train has a weight of 100 tons (2,000lbf) is stopped from 4 mph in 1 ft by a hydraulic cushion.If…

A:

Q: The jet aircraft has a total mass of 21 Mg and a center of mass at G. Initially at take-off the…

A: Given data with variables. m=21 Mg=21×103 kg2T=6 kNT'=2.1 kN   It is required to determine the…

Q: In Fig. 1, the box-fan of weight 22 N is hovering in the air. The air approaches the blades from the…

A:

Q: windmill has blades of length equal to 24 m and extracts 4% of the kinetic energy of the wind that…

A:

Q: In a standard wind turbine, the typical range of wind speed at which the wind turbine starts…

A: The typical range of wind speed for generating the power is equal to 3 m/s to 25 m/s or (0.83 km/hr…

Q: Consider a train consisting of an engine of mass 55 tonne pulling 10 trucks, each of mass 13 tonne,…

A: Part a:    Part b:     Part c: So, the change in potential energy of the train is 10.89  MJ.…

Q: explanation of the performance tests undertaken for a wind turbine. With the options found, give a…

A: given; performance test for wind turbine?

Q: Calculate the power available in the wind and the rotor power when the blade length for the turbine…

A:

Q: jet strikes a stationery curved vane without shock and is deflected 150° from its original…

A:

Q: A 3-bladed wind turbine with 250 kW generator has diameter of 50 m and tower height of 60 m. It is…

A: Turbines use propeller-like blades that operate like an aeroplane wing to capture wind energy. A…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.