A block of mass 2 kg is moving on a horizontal frictionless surface with velocity of 1 m/s, towards another block of equal mass initially at rest connected to spring. The other end of spring is fixed to the support. If the spring constant of the spring is 100 N/m, the maximum compression in the spring is

A block of mass 2 kg is moving on a horizontal frictionless surface with velocity of 1 m/s, towards another block of equal mass initially at rest connected to spring. The other end of spring is fixed to the support. If the spring constant of the spring is 100 N/m, the maximum compression in the spring is

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

A rectangular open tank is 6m long, 2m deep and 2m wide is containing water up to 1m height. If the tank is subjected to horizontal acceleration of 3 m/s2, find (i) angle of water deformation on the surface (θ) (ii) force on each end during acceleration (γ = 9790 N/m3)
The 1-m diameter sphere in the figure shown rests in static equilibrium against a frictioniess wallat B. Compute the speciic gravity of the sphere. 0.5m Water
The correct answer is option B. 0.82 m
1) A plug in the bottom of a pressurized tank is conical in shape as shown. The air pressure is 50 kPa and the liquid in the tank has a specific weight of 27 kN/m³. Determine the magnitude, direction and line of action of the force exerted on the curved surface of the 50 kPa Air Liquid cone within the tank due to the 50 kPa 3 m pressure and the liquid. 1 m 60°
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E 200, 000M Pa and %3D a = 11.7- Neglect bending of the beam. A=640mm2 A=320mm2 A C 1.2 m 0.8 m 1.2 m V 54KN 1. If there is no change in temperature, what is the deformation of rod C in mm? 2. If there is no change in temperature, what is the deformation of rod B in mm? 3. What is the stress of rod C if there is no change in temperature in MPa? 4. What is the vertical displacement of D in mm, if the temperature rises 50°C? 5. If the temperature rises, what is the thermal deformation of steel in mm?
4
4. An upright wine barrel contains 3 m depth of wine with relative density of 1.015. The barrel is 2 m in diameter and 4 m high. Since the barrel is closed, there is a pressure of y kPa (where y = 60 above the liquid surface. (a) Draw the free-body diagram of the barrel. (b) What is the total normal force in kg acting on the wall of the barrel? (c) What is its location from the ) due to air that fills the container bottom of the barrel in meters?
Solve and explain!
Specific gravity of a fluid is G=0.9 and viscosity -1.2 Pa-s. This fluid flows in a laminar regime between the two parallel plates fixed 3 cm apart. The discharge is 600 cm³/s/cm width of plate. Find the shear stress on the boundary in the units of Pa.
RIGID BODY TRANSLATION SHOW FREE BODY DIAGRAMCOMPLETE AND CLEAR SOLUTION DON'T ROUND OFF
The space between two square parallel plates is filled with oil. Each side of the plate is 75 cm. The thickness of the oil film is 10 mm. The upper plate which moves at 3 m/s requires a force of 100 N to maintain the speed. Determine:(1) The dynamic viscosity of the oil(2) The kinematic viscosity of the oil, if the specific gravity of oil is 0.9.
?