A block of mass 14 kg slides down an inclined plane at an angle of 45" with a massless rope attached to a pulley with mass 2.5 kg and radius 0.5matthe top of the incline (see the following figure). The pulley can be approximated as a disk with I-=2 MR-. The kinetic friction force on the plane is 8.3 N. What is the acceleration of the block? 45° Act

A block of mass 14 kg slides down an inclined plane at an angle of 45" with a massless rope attached to a pulley with mass 2.5 kg and radius 0.5matthe top of the incline (see the following figure). The pulley can be approximated as a disk with I-=2 MR-. The kinetic friction force on the plane is 8.3 N. What is the acceleration of the block? 45° Act

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 23 cm wrench is used to generate a troque at a bolt. a force of 51 N is applied at the end of the wrench at an angle of 51° to the wrench. The torque generated at the bolt is? Answer in N.m
Two blocks are connected to a rope, and the rope is hung over a pulley connected to the ceiling, as shown in the figure below. 1721 Mo i The masses of the blocks are m₁ = 16.0 kg and m₂ = 11.5 kg, the mass of the pulley is M = 5.00 kg, and the radius of the pulley is R = 0.100 m. Block m₂ is initially on the floor, and block m₁ is initially 4.20 m above the floor when it is released from rest. The pulley's axis has negligible friction. The mass of the rope is small enough to be ignored, and the rope does not slip on the pulley, nor does it stretch. (a) How much time (in s) does it take block m, to hit the floor after being released? At₁ S (b) How would your answer to part (a) change if the mass of the pulley were neglected? (Enter the time, in seconds, it takes block m, to hit the floor if the mass of the pulley were neglected.) At₂
An m 10.8kg mass is attached to a cord that is wrapped around a wheel of radius r= 11.9cm (see the figure below). The acceleration of the mass down the frictionless incline is measured to be a = 2.17m/s^2. Assuming the axle of the wheel to be frictionless, and the angle to be 8 = 36.5deg determine the tension in the rope. Submit Answer Tries 0/10 m Determine the moment of inertia of the wheel. ) Submit Answer Tries 0/10 Determine angular speed of the wheel 2.09s after it begins rotating, starting from rest.) Submit Answer Tries 0/10
Two blocks are connected to a string, and the string is hung over a pulley connected to the ceiling, as shown in the figure below. MG R m1 m2 The masses of the blocks are m, = 17.0 kg and m, = 10.5 kg, the mass of the pulley is M = 5.00 kg, and the radius of the pulley is R = 0.100 m. Block m, is initially on the floor, and block m1 is initially 5.00 m above the floor when it is released from rest. The pulley's axis has negligible friction. The mass of the string is small enough to be ignored, and the string does not slip on the pulley, nor does it stretch. (a) How much time (in s) does it take block m, to hit the floor after being released? At, = (b) How would your answer to part (a) change if the mass of the pulley were neglected? (Enter the time, in seconds, it takes block m, to hit the floor if the mass of the pulley were neglected.) At,
3 Geodynamo The mass of the earth is M = 6.0 x 1024 kg and its radius is R = 6.4 x 10° m. (a) Estimate the rotational kinetic energy of the earth, in joules (J). (b) The world's annual power consumption is about 20 TWh. If the earth's rotational kinetic energy could be converted to electrical power, how long could it supply energy to the human race, assuming our power consumption remained constant? Report your answer in seconds and in years.
A turn table starts from 10 rad/s of angular velocity and slows down to a stop in 5.0 s. Find the total angle turned during this time, in rad. Hint: use rotational kinematics formula. Assume initial angle and final angular velocity as zero.
Problem 2 The Pulley in the figure. is made up of two coarial wheels that are glued together so that they form a single objects. The radi their masses. of the wheels are Ri = 0,30m and R₂ = 0, bom; are M₁ - Boung and M₂ = 10.0ng. An in extensible string is wrapped around the cylinder 2.40 kg attached to the of the two wheels actes a un of radius R₁ and mass m2 = Spring. On the axus uniform fructional torque to. At the beginning the system is at rest. At time t = Os the mass m starts to go down and after a length h=1.5m the mass comes down to the ground with speed of 1,38 mls. a) the tension the string and the fructional torque to b) When the mass comes to ground, the string disengages turns done from the cylinder. Find the number the wheels before it stops. of by B₂ R₂ I'm ↑ h =1,5m Please answer the above question step-wise, showing detailed explanations ( in handwritten if possible) Thanks in advance
A 1.0-kg mass hangs on a rope wrapped around a frictionless disk pulley of mass 5 kg and radius 0.5 m. What is the acceleration of the mass? (The moment of inertia of the pulley is 1/2MR2.)
Needs Complete typed solution with 100 % accuracy.
Needs Complete typed solution with 100 % accuracy.
In the figure, what magnitude of force F applied horizontally at the axle of the wheel is necessary to raise the wheel over an obstacle of height h = 0.281 m? The wheel's radius is r = 0.718 m and its mass is m = 1.28 kg. O Number Units h
An Atwood's machine consists of blocks of masses m,- 13.0 kg and m₂ - 16.0 kg attached by a cord running over a pulley as in the figure below. The pulley is a solid cylinder with mass M-7.80 kg and radius r=0.200 m. The block of mass m₂ is allowed to drop, and the cord turns the pulley without slipping. 7₁ (a) Why must the tension T₂ be greater than the tension T₂? This answer has not been graded yet (b) What is the acceleration of the system, assuming the pulley axis is frictionless? (Give the magnitude of a.) m/s (c) Find the tensions T₁ and T2 T₂-