M=22.5 ib-in A bimetallic beam used in a temperature-control switch consists of strips of aluminum and copperbonded together as shown in the figure, which is a cross-sectional view. The width of the beam is1.0 in., and each strip has a thickness of 1/16 in.Under the action of a bending moment M =22.5 |b-in. acting about the z axis, what are themaximum stresses oą and o, in the aluminum and copper, respectively? (Assume Ea = 10.5 x106 psi and E. = 16.8x 106 psi .)in.161.0 in.in.16

Name: M=22.5 ib-in A bimetallic beam used in a temperature-control switch co
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: M=22.5 ib-in A bimetallic beam used in a temperature-control switch consists of strips of aluminum and copperbonded together as shown in the figure, which is a cross-sectional view. The width of the beam is1.0 in., and each strip has a thickness of 1

Answered: Image /qna-images/answer/f2dd2135-cf85-417b-ae95-a506e94b49ef.jpg

Engineering

Mechanical Engineering

A bimetallic beam used in a temperature-control switch consists of strips of aluminum and coppe bonded together as shown in the figure, which is a cross-sectional view. The width of the beam i 1.0 in., and each strip has a thickness of 1/16 in. Under the action of a bending moment M =22.5 Ib-in. acting about the z axis, what are the maximum stresses oą and o, in the aluminum and copper, respectively? (Assume Ea = 10.5 x %3D 106 psi and E. = 16.8x 106 psi .) %3D

A bimetallic beam used in a temperature-control switch consists of strips of aluminum and coppe bonded together as shown in the figure, which is a cross-sectional view. The width of the beam i 1.0 in., and each strip has a thickness of 1/16 in. Under the action of a bending moment M =22.5 Ib-in. acting about the z axis, what are the maximum stresses oą and o, in the aluminum and copper, respectively? (Assume Ea = 10.5 x %3D 106 psi and E. = 16.8x 106 psi .) %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
B=55⁰ inside diameter = 28.6in. wall thickness=0.35 in. allowable normal stress perpendicular to the weld = 18 ksi allowable shear stress parallel to the weld =8 ksi What is the largest gage pressure inside the tank? Answer in psi rounded-off to 3 decimal places K
Find the Normal Stress at points A, B, and C in the Rod below. Dimensions given are diameters.
The state of stress at a point in a machine component is given by ox = 120 MPa, oy = 55 MPa, Oz = -85 MPa, Oxy = -55 MPa, Oxz = -75 MPa, and oyz = 33 MPa. Construct the Mohr's circles of stress for this stress state and find the maximum shear stress.
Fined the stress in each segment and the displacement in each segment
A spherical tank of diameter 0.98 m and wall thickness 36 mm, contains compressed air at a pressure of 33 MPa. What is the absolute maximum shear stress? Lütfen birini seçin: a. 112.3 MPa b. None c. 108.8 MPa d. 120.8 MPa e. 67.73 MPa
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
Solve show solution
Find maximum principal stress
at question A=110 MPa B=-60 MPa M=145N.m
Q1. Find the shear stress in aluminum and Steel TAI, TS Use: Gsteel = 85 GPa, GAI= 30 GPa Aluminum Steel D=150 mm D = 50 mm T = 3 kN.m 2.5 m 0.5 m
Solve 1st problem