A beam of size 250 mm width and 460 mm effective depth is subjected to limit state moment of 146 kNm. If M20 grade concrete and Fe415 steel are used, the area of steel required will be (a) 435 mm2 (c) 1100 mm2 (b) 935 mm2 (d) 1235 mm2

A beam of size 250 mm width and 460 mm effective depth is subjected to limit state moment of 146 kNm. If M20 grade concrete and Fe415 steel are used, the area of steel required will be (a) 435 mm2 (c) 1100 mm2 (b) 935 mm2 (d) 1235 mm2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield strength fy=415 MPa The section is to be reinforced for tension only and the effective concrete cover is 65 mm. Which of the following most nearly gives the value of our balanced steel ratio? a. 0.00370 b. 0.03456 C. 0.02860 d. 0.03522 Which of the following most nearly gives the value of our balanced distance of the cuter most fiber of compression fiber to our neutral axis? a. 313.256 mm b. 354.68 mm C. 333.333 mm d. 322.435 mm Which of the following most nearly gives the value of our balanced depth of compression block? a. 248.412 mm b. 266.2676 mm C. 301.478 mm d. 281.261 mm
A rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psi
SITUATION. Given: BxH 400 mm x 500 mm As = 6 x 20 mm Ø diameter bars Clear concrete cover to 10 mm diameter ties = 50 mm Concrete fc' = 28 MPa Steel fyl = 415 MPa Steel fyv 275 MPa Ø=0.75 If the column is replaced with a 400mm diameter section and the nominal shear capacity of concrete is 1.20 MPa, which of the following most nearly gives the nominal shear strength (kN) of the concrete, Vc? O260 150 = 260 150
FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Calculate the uniform load (in addition to the beam weight) which will cause the section to begin to crack if they are used for 28 ft simple span. = 4000 psi , the modulus of rupture f, = 7.5f',, and reinforced concrete weight is 150 lb/ft³. 15" 18" 2 #8 3" 12"-
The working load capacity of a column of size 300 mm x 600 mm with minimum percentage of steel is the value as nearest integer.) kN. Assume grade of concrete as M20 and grade of steel as Fe415. (Give
A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy = 414 MPa. Calculate the nominal capacity based on the maximum steel area for a tension- controlled condition. Use the following dimensions: b = 498 mm d = 709 mm t = 152 mm web thickness - 152 mm b 1 I d
A RC beam of cross section 220 × 460 mm is subjected to following forces: Factored shear force = 30 kN Factored bending moment = 35 kNm Factored torsional moment = 5 kNm What should be the minimum area of tension steel provided such that there is no need to provide torsional reinforcement. Use M20 grade concrete and Fe415 grade steel. Use the following data for M20 grade concrete. 100 As 0.50 0.75 1.00 1.25 1.50 bd Design shear stress (N/mm²) 0.48 0.56 0.62 0.67 0.72
PROBLEM: A rectangular reinforced concrete beam has a width of 310 mm and an effective depth of 490 mm. Concrete compressive strength (fc') is 21 MPa, and steel yield strength (fy) is 345 MPa. Use USD Method. DETERMINE: 4. Ultimate moment capacity if the beam is reinforced with 8 – 25 mm diameter tension steel. 5. Ultimate moment capacity if the beam is reinforced with 10 – 25 mm diameter tension steel.
| Choose the most appropriate answer for the following: 4. One of the following is not correct for pre-stressed concrete: a. Reducing cracks in the concrete b. High strength of concrete and steel c. Costy d. Suitable for long span and those carrying heavy loads. 5. Cross ties are used if the distance between a bar and the corner bar is greater than... 100 inches b. 100 cm c. 150 inches d. 150 mm а.
PROBLEM: A rectangular reinforced concrete beam has a width of 310 mm and an effective depth of 490 mm. Concrete compressive strength (fc') is 21 MPa, and steel yield strength (fy) is 345 MPa. Use USD Method. DETERMINE: 1. Ultimate moment capacity if the beam is reinforced with 4– 25 mm diameter tension steel. 2. Ultimate moment capacity if the beam is reinforced with 5 – 25 mm diameter tension steel. 3. Ultimate moment capacity if the beam is reinforced with 6 – 25 mm diameter tension steel. 4. Ultimate moment capacity if the beam is reinforced with 8 – 25 mm diameter tension steel. 5. Ultimate moment capacity if the beam is reinforced with 10 – 25 mm diameter tension steel.
Details of a rectangular column are as follows: Column width along the x-axis = 250 mm Column width along the y-axis = 600 mm Reinforcement 8 of 25 mm diameter bars distributed equally along the longer sudes 10 mm diameter ties spced 100 mm on centers. Concrete 28th dat compressive strength, fc' = 20.7 MPa Reinforced steel yield strength, fy = 415 MPa Assume that the compression steel yields. Concrete cover to the centroid of bars 70 mm Determine the nominal balanced load with eccentricity measure from the y-axis if the depth of the rectangular concrete compressive stress block is 90.66 mm.
a t-beam has the following properties; bf = 820mm, bw = 250mm, d = 470mm and tf = 100mm. Concrete compressive strength is 20.70 MPa and the steel yield strength is 414 MPa. Determine the number of bars need if MDL = 150 kN-m and MLL = 120 kN-m. Use 25 mm bar. What is the steel area needed?