A beam is subjected to a system of coplanar forces as shown in the figure. The magnitude of vertical reaction at Support P is N. (round off to one decimal place). 500 kN 60° 0.5 m 100 kN 2 m 1.5 m 1 m-1.5 m - 200 KN

Q: Find the area and put in square feet

A:

Q: Determine the X coordinates of the centroid of the trapezoidal area shown.

A: Given data : The given figure in divided into Rectangle and Triangle Rectangle: Width (B)=120 mm…

Q: Give other methods of determining the horizontal distance between two points.

A:

Q: 1/2x10ft

A: We are given: 1/2×10 ft   The given expression is equivalent to computing half the length of 10 f.

Q: Can you explain how did you het Tab = 1160.695N, Tac...., Tad.....? Just go over equations for last…

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral.…

A:

Q: What is the area of a circle 2.75 ft in diameter?

A: Given: The diameter of the circle is 2.75 ft.

Q: Show the quadrants of a circle and within the circle show  S 30° W

A:

Q: Compute for the area of the cross section, considering b is 6.4 meters: 6.24 9.44 + 4.40 + 2.90 +…

A:

Q: Find the area of each. Then put in square feet and square yards

A: 18.19.20.21.22.

Q: ARSWer ls With reference to the units systems, One full circle equals 400 Grades 180 15 30 2 TT

A: One Full Circle equals to 400 GRADES  And also 2π radians and 360°

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: Given the table below, compute the area of the traverse by coordinates method. Traverse 6 X-coor…

A:

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: midpoint approximation

A: Midpoint Approximation: The midpoint approximation or the midpoint rule is used for calculating the…

Q: Describe about the Taylor Charts.

A: Taylor's stability chart are used for determining the stability of slope of cohesive homogeneous…

Q: A line was measured as 79.52 Chains. What is the length of the line in feet? (to nearest 0.1 foot)

A: 1 chain = 66 feet 79.52 chains = 79.52 x 66                         = 5248.3 feet

Q: determine the centroid of the area shown with respect to the given x-axis

A:

Q: Determine the coordinates of the centroid of the shaded area. | 20 40 50 20 50 60 40 140 Dimensions…

A: Determine coordinates centroid of the shaded area

Q: Give the vector in cartesian coordinates that extends from B(4, 20degrees, 10degrees) to W(7,…

A: The given data is shown below: B=4,20 degrees, 10 degreesW=7,120 degrees, 75 degrees

Q: 610 mm 813 mm y 1220 mm 660 mm

A: Given Data  volume is given cuboid and right angle triangular prism with x=1220 mm y=813 mm z=660 mm…

Q: why divide x' in 2 in above method?

A: ##Calculation of location of x at such that due to given loading a  Maximum BM occurs ### As ask…

Q: 6"

A:

Q: convert 284.366 decimal angle into degrees, minutes, and second.

A: Givend=284.3661Degree=60'1'=60''so1degree=3600''

Q: How many divisions are on the vernier scale?

A: A vernier scale is a visual representation that uses mechanical approximations to obtain an exact…

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: How did you get the 24.35 kips

A:

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: why 3.5 instead of 2.5?

A: Correct solution is provided below

Q: نقطتان )2( Shows polygon with the followng :Find the area (x,y) 2 1.8 1.6- 1.4- 1.2 0.8 0.6- 0.4…

A: answer is option a.)   Matlab command window picture is attached below

Q: Where are the numbers 7.1 and 0.0013 from?

A: Given equations For PM: Perticulate MatterCmax (PM) = 7.1 x (Q / H) x (1 - exp (-2.303xKxH))Xmax…

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 26 54…

A:

Q: 1.00 - D 30° - Ø1.00 F Ø1.00 в 4.00 2.50 2.00 1.50 E 3.00 A 5.50

A: Absolute Coordinates system is where we show location by cartesian coordinate with reference to one…

Q: Describe the structure of the surveyor’s compass.

A: The large surface when undulated the process used for surveying is known as surveyor's compass.

Q: Locate the X–X and Y–Y centroidal axes for the area shown.

A:

Q: Which shape has more sides than a quadrilateral?

A: A polygon is a two-dimensional shape that is formed by a set of line segments forming an enclosed…

Q: 9. Using cantilever method, determine the maximum absolute axial force in the column in kN due to…

A: Given data in question  Lateral loading Dimensions  Cantiler method  To find out  Axial forces in…

Q: 1 / 2 \text { inch } \times 1 / 4

A: To find:- 1/2*1/4

Q: 2ft

A: Given  Triangle of height 2ft  Slope : 3H to 4V

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.