A beam is simply supported and has a span of 12 m. The beam is a W33x240 with Ex=345 MPa. Compute the following: A. If the compression flange is fully braced laterally. Express your answer in kN/m. (ASD) B. If the compression flange is fully braced laterally. Express your answer in kN/m. (LRFD) Properties of W33x240: Weight = 3.51 kN/m A = 45,548 mm² d = 850.9 mm b₁ = 402.97 mm t₁ = 35.56 mm tw = 21.08 mm Ix = 5,660.75 x 108 mm² ly = 388.34 x 10 mm* Sx = 13,322.68 x 10³ mm³ Sy = 1,933.67 x 10³ mm³ rx = 352.54 mm ry = 92.34 mm Jc = 14.51 x 10 mm Its = 105.92 mm

A beam is simply supported and has a span of 12 m. The beam is a W33x240 with Ex=345 MPa. Compute the following: A. If the compression flange is fully braced laterally. Express your answer in kN/m. (ASD) B. If the compression flange is fully braced laterally. Express your answer in kN/m. (LRFD) Properties of W33x240: Weight = 3.51 kN/m A = 45,548 mm² d = 850.9 mm b₁ = 402.97 mm t₁ = 35.56 mm tw = 21.08 mm Ix = 5,660.75 x 108 mm² ly = 388.34 x 10 mm* Sx = 13,322.68 x 10³ mm³ Sy = 1,933.67 x 10³ mm³ rx = 352.54 mm ry = 92.34 mm Jc = 14.51 x 10 mm Its = 105.92 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A W36x210 can be used for Transfer Girder ‘A’ as shown in the elevation next page.Assume the LRFD loads on the ‘Transfer Girder’ are as follows:Pu= 200 kips from the column above. Assume also that the loads from self-weight of thewu = 2.0 kip/ft (girder self weight and beams framing into this transfer girder are equivalentto a uniformly distributed load). These loads are shown in the last figure.a) Check whether the W36x210 ‘Transfer Girder’ is adequate for bending and shear.Assume the unbraced length Lb =20 ft.b) Suppose that service loads, w and P, are both 50% dead load and 50% live load. Does theW36x210 satisfy a service live load deflection limit of L/480?
Homework 1- For a simply supported beam with span 6.0 m , determine the area of steel required to reinforced the beam(350*550) mm if it subjected to service dead load (including to self-weight) (40 kN/m) and service concentrated live load (PL 100 kN) use f'c = 25 MPa & fy 350MPA P= 100 kN Wdl= 40 kN/m 550 mm 350 mm
choose final letter of answer
?
Please correct solution
A reinforced concrete T-beam is to be designed for tension only. The beamwidth is 250 mm. effective depth to bottom bars is 400 mm, flange thickness is 100mm, simple span is 3.6 m and beam spacing is 1.2 m on centres. If the applied designmoment is 300 kn-m, fc’ = 20.7 MPa and fy = 414 MPa. Determine the effective widthof the compression flange and the number of 28 mmφ diameter bars necessary forthe beam.
Q1/ Calculate (b, d, h and As) for the cantilever beam shown below if the applied point load (Pa 78.5 kN and PL=100 kN) and fe = 35 MPa and f 400 MPa: P. Pa 3.5 m I m
A reinforced rectangular beam with width b and effective depth d is subjected to service live and dead loads (self-weight included) of wL and wD, respectively. If required, compression steel bars are to be placed at a distance d' from the extreme compression fiber. Use fe' = 28 MPa and fy 420 MPa. b= 100 mm d= 200 mm d'= 300 mm L= 320 m wL 210 kN/m wD= 220 kN/m 1. Solve for the area of tension steel bars using es 0.004. 2. Solve for the area of compression steel bars using es 0.004. 3. Solve for the area of tension steel bars using es = 0.005. 4. Solve for the area of compression steel bars using es = 0.005.
Thank you
Example 2 (H.W) : For the simply supported beam of section shown in figure below, calculate the flexural stresses at ends and mid-span at all loading stages, then check these stresses with ACI limitations use fei' = 29 MPa, fe'= 35 MPa, Fpi= 1300 MPa, final losses =20 % live load= 5 kN/m, dead load =5 kN/m in addition to its own weight, span length= 13 m, class U and all live load is sustained. 600 mm 75 mm 700 mm I 50 mm 100 mm 100 mm
A composite beam spans a distance of L= 12 ft and is fabricated by adhering two wooden boards (b= 2 in., d= 8 in. and E = 1,500 ksi) to the sides of a steel plate (t = 0.4 in., d = 8 in. and E= 30,000 ksi). 400 lb 400 Ib 200 lb/ft d -3 ft- 3 ft V (lb) -6ft 600 400 (ft) 12 -400 -600 1. For the given loading condition, determine the maximum normal stress M (lb-ft) in the steel plate. A) 3,850 psi +x (ft) B) 1,550 psi -300 C) 2,250 psi D) 4,200 psi -1200 - 1200 E) None of the Above 2. If the allowable normal stress of the steel is 9,000 psi and the 200 lb/ft distributed load remians constant, determine the largest acceptable concentrated load on each end. A) 1,600 lb B) 2,325 lb C) 935 lb D) 860 lb E) None of the Above
A reinforced concrete T-beam has the following properties: beff=1360mm, tf=150mm, bw = 300mm, d=610mm, Asbot= 9920mm2, fc’=28MPa, fy=414 MPa. Calculate the design moment capacity of the section for positive bending in kN-m. Express your answer in 2 decimal places.