A beam is part of the framing system for the floor of an office building. The floor is sub- jected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor o of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC load combination? d. What is the required nominal moment strength for a safety factor 2 of 1.67?

A beam is part of the framing system for the floor of an office building. The floor is sub- jected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor o of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC load combination? d. What is the required nominal moment strength for a safety factor 2 of 1.67?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Kindly box final answers and write solutions neatly
PROBLEM 3 THE BUILDING IN FIG. P1.1 IS USED FOR LIGHT STORAGE SPACE. THE SLAB 16 250 MM. THICK. THE BEAMS ARE 400 MM. WIDE AND HAVE A TOTAL DEPTH OF 500 MM, THE BAY DIMENSIONS ARE 6M IN THE X DIRECTION AND 7.5 M IN THE Y DIRECTION, AND THE CUPERIMPOSED SPRINKLER DEAD LOAD IS 0-25 KPA. CALCULATE THE SLAB FACTORED LOAD IN KPA AND THE BEAM FACTORED LOAD IN KN/M. SOLUTION:
Refer to the below diagram and the booking sheet Question: What is the number (or word/s) which must be CP 1 2.050 entered into the levelling booking sheet that is marked as: B.M. 11 RL 0.724 OP 2 3.100 (Note, if the space should have nothing written in it please 16.235 2.785 2.565 2.480 answer NONE) Set up 1 Set upa B = NONE LEVELLING BOOKING SHEET B.S. I.S. F.S RISE FALL F = 2.050 R.L. REMARKS A B G) F. H) -2.145 2.570 2.410
please help thann you
Kindly box final answers and write solutions neatly
Convert: 290.502 grad to mils.
The value of A is Blank 1 meters D ... ROADWORK AHEAD 80 60 Direction of Travel Work Area PREPARE 80 60 то 2D D STOP D A B C ROADWORK AHEAD
QUESTION 2 Glven the technical description of a certain lot, complete the tables below: DIST 40.311 38.910 37.014 51.140 LINE AB BC CD DA Station A B с D BEARING N 60° 15.3¹ E S 64° 5.6' E S 42° 29.2¹ W N 61° 38.1' W interior < division gnerating fr. * Express all values up to 3 decimal places. * If the value is zero just write 0. A Area 1 Area 2 Total * If the value is negative, include the negative sign without space in between negative sign and the number. Example: value = -37, input: -37.000 * For positive values, do not include the + sign in writing the answer. *Do not include the unit in writing the answer/s.
Glven the technical description of a certain lot, complete the tables below: DIST 38.588 37.736 28.278 83.100 LINE AB BC CD DA Station A B C D BEARING N 58° 46.9' E S 57° 59.7¹ E S 30° 46.5' E N 73° 0' W interior < division gnerating fr. B Area 1 Area 2 Total * Express all values up to 3 decimal places. * If the value is zero just write 0. * If the value is negative, include the negative sign without space in between negative sign and the number. Example: value = -37, input: -37.000 * For positive values, do not include the + sign in writing the answer. * Do not include the unit in writing the answer/s.
Redrawing the scheme in the manner of "activities on the contract"
HELLO PLEASE HELP, WITH COMPLETE SOLUTION. PLEASE DO NOT MAKE IT COMPLICATED THANK YOUU! 4 DECIMAL PLACESS
bint Pr X y Term ProjectCx y SURP 816: Phy X E TEC 3739 Gro x M V Lab Example E Foundation HV x Phase 2 Repor X A asulearn.appstate.edu/mod/quiz/attempt.php?attempt=3358733&cmid%3D2173348 as learn A ULC C3739-101_MATERIALS AND STRUCTURES III (SPRING 2022) ard/ My courses / Spring 2022 / TEC3739101-12999202210 (SPRING 2022) / HOMEWORK / Foundation HW - Part III (Due date: 04/04/2 n1 Please round to the nearest One (i.e., 1). No Comma! The results of a plate-load test in a sand soil are shown below. The size of the plate is 0.275m x 0.275m. If a square column foundation (5m x 5m) that should carry a load of 5000kN, what is the estimated settlement of the ed out of foundation? Load/unit area Settlement Load/unit area (kN/m?) (KN/m?) (mm) 800 200 400 600 200 6 300 10 400 13 500 20 20 600 29 30 40 50 60 70 Answer = mm MacBook Air Settlement (mm)