A beam having the cross section shown is subjected to a couple that acts in a horizontal plane. Determine the largest permissible value of the moment Mo of the couple if the maximum stress in the beam is not to exceed 9 ksi. Given: ly=/₂=11.3 in 4 A=4.75 in² kmin = 0.983 in. Z 0.5 in. 1.43 in. с B ← 0.5 in. 5 in. 1.43 in. Y The largest permissible value of the moment Mo is 5 in. kip-in.

A beam having the cross section shown is subjected to a couple that acts in a horizontal plane. Determine the largest permissible value of the moment Mo of the couple if the maximum stress in the beam is not to exceed 9 ksi. Given: ly=/₂=11.3 in 4 A=4.75 in² kmin = 0.983 in. Z 0.5 in. 1.43 in. с B ← 0.5 in. 5 in. 1.43 in. Y The largest permissible value of the moment Mo is 5 in. kip-in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The curved bar shown in the figure has a rectangular cross section of 50x75 mm and an internal radius of 125 mm. For a force F = 1200 N, determine: a-) the normal stress at point A. b-) the normal stress in point B.
Question 4: A machine of 540 kg is bolted at the middle of two parallel simply supported steel beams. The clear span of the beam is 2.4 m. The moment of inertia of the cross-section of each beam is I = 4.2×10¯6 mª. The Young's modulus of the steel is E 200 GPa. When the machine is operating, it will generate a vertical force P(t)=Posinot. When the machine runs at 300 rpm, Po= 1500 N. Neglect the weight of the beams and assume 2% viscous damping in the system. Determine the amplitude of steady-state deflection of the beams at their midpoint when the machine runs at 300 rpm. machine 1.2 m = 1.2 m Steel beams
Figure shows the state of stress of a plane-stress element. Determine the principal stresses. Show the state of stress on a properly oriented element. Determine the maximum shear stresses. Show them on a sketch of a properly oriented element. Determine the value of the shear stress for an element having a normal stress of 40 MPa. Draw the state of stress on a properly oriented element.
184 What is the strain energy of the massless stepped bar as shown in the figure below? [Take E= 200 GPa] (a) 0.38 N-m (c) 0.50 N-m 30 mm 10 mm 100 mm 20 mm 120 mm • ** ** 80 mm 10 kN (b) 0.42 N-m (d) 0.56 N-m
Q.b.
A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (see figure). P The tank has an inner radius of r = 141 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 820 N m. (Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 169 MPa? (Enter the magnitude in kN.) KN (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank (in MPa)? MPa
An element is subjected to plane stresses as shown in Figure Q1. (i) Determine the normal stress and shear stress acting on the plane that is inclined at 20° as shown in the figure. (ii) Determine the principle major and minor stress and the orientation of the plane where the stresses acting. (iii)Determine the maximum shear stress and the orientation of the plane. 10 N/mm² 30 N/mm² 50 N/mm² 2007 50 N/mm² 30 N/mm² 10 N/mm²
Determine the equivalent state of stress on an element at the same point oriented 60" clockwise with respect to the element shown in the figure below. Suppose that =153 MPa =D 109 MPa (Figure 1) Figure 1 of 1 75MPA
Situation 10: The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two rods. Initially, the bar is horizontal and the vertical rods are stress-free. The temperature in the steel rod is decreased by 40°C. Neglect the weight of the bar Steel L = 910 mm A = 300 mm² E = 200 GPa a = 11.7 x 106/C AT = -45°C 0.5 m + 1.3 m Aluminum L = 1320 mm A 1200 mm² E = 70 GPa a = 23 x 106/C 27. Determine the stress in the aluminum rod 28. Determine the stress in the steel rod 29. Determine the deflection at the point where aluminum rod and bar is attach
A steel wire is bent into an arc of a circle of radius 5m. Find the maximum bending tensile stress induced in the wire. The diameter of the wire is 40 mm. Take E = 2 × 106 kg/cm².
Give me right answer. **For the Structure Shown, Circle the Equation(s) that you would use to compute the normal and shear stress at point K Not necessary to solve. just circle the equations.
A rectangular piece of material is subjected to tensile stresses of 83 and 65 N/mm on mutually perpendicular faces. Find the strain in the direction of each stress and in the direction perpendicular to both stresses. Determine also the maximum shear strain in the plane of the stresses, the maximum shear stress and their directions. Take E=200 000 N/mm² and v=0.3. Ans. 3.18×10 4, 2.01×10-4, –2.22×10-4, 7max=1.17x10-4, Tmax=9.0 N/mm² at 45° to the direction of the given stresses.