A beam carries a concentrated load W and a total uniformly distributed load W. (N/m). Whatsafe value of W (Newton) can be applied if fbc < 100 MPa and fot s 60 MPa at negative valuebending moment? Show the equation of the positive bending moment.175 mmWoN.A.125 mm-2 m-4 mR1R2INA = 24 x 104 mm

unsymmetrical beam - Flexural Stress varies directly linearly with distance from the neutral axis…

A beam carries a concentrated load W and a total uniformly distributed load wo (N/m). What safe value of W (Newton) can be applied if fac S 100 MPa and fot S 60 MPa at negative value bending moment? Show the equation of the positive bending moment. w [75 mm N.A. 125 mm -2 m- R1 R2 INa = 24 x 10ʻ mm

A beam carries a concentrated load W and a total uniformly distributed load wo (N/m). What safe value of W (Newton) can be applied if fac S 100 MPa and fot S 60 MPa at negative value bending moment? Show the equation of the positive bending moment. w [75 mm N.A. 125 mm -2 m- R1 R2 INa = 24 x 10ʻ mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PLEASE ANSWER ASAP THANK YOU
H.W Draw S.f,B.M and elastic dliagrams for the beam Shown below by method of equntions ? 6W/m 20 KN 6m 2m 2m
Consider the figure 1 below: 3-25mmø bolts are used to fasten a plate to a steel beam a) Determine the average shearing stress caused in each bolt by the 30kN loads. b) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 6OMPA. 30 kN 150 300 200 P 30 kN 75 Foot
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
can you write the answer please
Topic: COMBINED STRESS - STEEL DESIGN
How to solve this question step by step
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
For the given properties of the beam below, determine the safest wy that the beam will carry. bf = 800mm bw = 500mm tf = 90mm d = 375mm d' = 100mm fc' = 34.5MPa fy = 400MPa As = 8-32mm bars The answer is kN/m bf + A, D +bw t f Wu A को + Pu 50 5m KN (Factored) load B +im+
It is not graded question and it is complete question.Plz, solve it for your understanding.Structural Analysis-2Plz, write as this process: Given Data Required solution Results Attempt Neat and Clean with proper diagrams
Answer 15&16