Answered: A BCD-to-7 segment decoder has 0100 on…

A BCD-to-7 segment decoder has 0100 on its inputs. The active outputs are(a) a, c, f, g (b) b, c, f, g(c) b, c, e, f (d) b, d, e, g

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 9VE

See similar textbooks

Related questions

Q: The BCD to 7-segment decoder combinational circuit has four inputs for the BCD digi and seven…

A: The BCD to 7-segment decoder combinational circuit has four inputs for the BCD digit and seven…

Q: Design logism circuit using AND, XOR and OR for ripple carry adder which is capable of adding two…

A: Introduction: In Digital Circuits, A Binary Adder-Subtractor is one that is capable of both the…

Q: Design a circuit that will multiply BCD ( Binary Coded Deciamal code) numbers which are between 0-9…

A: given BCD 0-9 Output = input x 10 if input is 0 [(0000)BCD] output = 0 x10 =0 [(0000 0000)BCD] if…

Q: Using an 4X1 multiplexer module to implement the Boolean function f(a,b,c)=b+ac′

A: To implement the Boolean function f(a,b,c)=b+ac using a 4x1 multiplexer (MUX) module, you can follow…

Q: 3. Write a HDL code for 2bit binary DECODER.

A: This is the answer to question number 3. HDL code for 2bit binary DECODER following is

Q: Design a circuit to convert a 4-bit binary code to a 4-bit virgin reflective code (GRAY). Use a 4X16…

A: Circuit diagram for the above question is in step2.

Q: Design a 5 X32 decoder with 2X4 decoders with Enable input and a 3X8 decoder without Enable input

A: Answer to the above question is in step2.

Q: Problem 2 Design a combinational circuit with inputs a, b, c, d and outputs w, x, y, z. Assume that…

Q: Design a 4-to-16 decoder using 2-to-4 decoders with enable input.

A: 4×16 decoder can be implemented using five 2x4 decoders in which two selection line are given to a…

Q: If a 1-of-16 decoder with active-LOW outputs exhibits a LOW on the decimal 12 output, whatare the…

A: Given: If a 1-of-16 decoder with active-LOW outputs exhibits a LOW on the decimal 12 output, whatare…

Q: If we design a half subtractor circuit using two 2 x 1 multiplexers a, then the inputs to the first…

A: Answer: (1)- Difference.(2)- Borrow out.

Q: design a 3-bit squarer circuit (b2 b1 b0)2example if input is 4 so the output will be 4^2=16 The…

A: design a 3-bit squarer circuit (b2 b1 b0)2example if the input is 4 so the output will be 4^2=16 The…

Q: Design a 2-bit magnitude compactor using 4x16 decoder and also Implement given below Boolean…

A: Magnitude compactor which refers to combinational circuit that can compares the two digital and the…

Q: Given two 8-bit unsigned numbers, A and B:Using MSI components (comparators, multiplexers) design a…

A: Comparators: A comparator circuit compares two voltages and outputs either a 1 or a 0 to indicate…

Q: The IC used for BCD to 7 segment decoder is 74LS42

A: The given statement, The IC used for BCD to 7 segment decoder is 74LS42 is FALSE.

Q: D gates. Given two 8-bit signed 2s-complement numbers A and B and a binary input signal M, your…

A: Design a circuit that uses 4-bit full adders and AND gates. Given two 8-bit signed 2s-complement…

Q: Design and draw an 11-to-2^11 decoder with a) No predecoding. b) With predecoding. It is known that…

A: According to the question we need to design and draw an 11 to 2^11 decoder with a) No precoding b)…

Q: Design a combination circuit that allows to add two digits BCD 8421. The inputs and outputs will be…

A: A seven-segment display is an electronic device that consists of seven light-emitting diodes (LEDs)…

Q: Design the circuit F (A, B. C. D) = (0, 1, 2, 7, 8. 9, 14, 15) using 3 of 8 decoder

A: The 3 to 8 line decoder is also known as the Binary to Octal Decoder. In line 3 to 8, there are a…

Q: Design a 5X32 decoder with 2X4 decoders.

A: Given:

Q: Design a combinational circuit that detects the inputs not divisible by 2 or 5 in 4-bit data (0 is…

Q: Design a 16 bit adder/subtractor with 2 data inputs (B15 to B0 and A15 to A0), a SEL input (1 if add…

A: SOLUTION - Note: In this control input in your selection input when it is 0 it takes addition and…

Q: multiplier is to be designed for two 2-bit inputs using the algorithm. (Draw schematic, truth table,…

A: In the above calculation, A1A0 is the multiplicand. B1B0 is the multiplier. The first product…

Q: write a bcd to 7 segment display using decoder in logisim

A: Given: Describe & implement a bcd to 7 segment display using decoder in Logisim.

Q: An 8 x 1 multiplexer has inputs A , B , and C connected to the selection inputs S2 , S1 , and S0 ,…

A: a) ANSWER: F(A,B,C,D)=Ʃ(1,6,7,9,10,11,12)

Q: Design a sequence detector circuit using the mealy model to detect when a value is not BCD, for…

A: A sequence detector circuit is a digital circuit that detects the occurrence of a specific sequence…

Q: 1. The waveform shown in Figure 12-45 is applied to a sampling circuit and is sampled every 3 ms.…

A: Given:

Q: Design a-full subtractor with two multiplexers (MUXS) S(x.y.2) = E( ... ), Cay Σ ) . Connect the…

A: Inputs Outputs X Y Z(Bin) Bout (Borrow) D (Difference) 0 0 0 0 0 0 0 1 1 1 0 1 0 1 1 0 1 1…

Q: Design a circuit using a Multiplexer, (((USING A MULTIPLEXER NOT A DECODER))) that has two inputs…

A: A computer is a digital electronic machine that can be programmed to automatically perform a series…

Question

A BCD-to-7 segment decoder has 0100 on its inputs. The active outputs are
(a) a, c, f, g (b) b, c, f, g
(c) b, c, e, f (d) b, d, e, g

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Fundamentals of Boolean Algebra and Digital Logics

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Design a combinational circuit that detects the inputs not divisible by 2 or 5 in 4-bit data (0 is divisible by all numbers).
Using an 4X1 multiplexer module to implement the Boolean function f(a,b,c)=b+ac′
Problem 2 Design a combinational circuit with inputs a, b, c, d and outputs w, x, y, z. Assume that the inputs a, b, c, d represent a 4-bit signed number (2s complement). The output is also a signed number in 2s complement which is 1 greater than the input if the input is less than 3, and is 2 less than the input if the input is greater than or equal to 2.
design a 3-bit squarer circuit (b2 b1 b0)2example if input is 4 so the output will be 4^2=16 The following truth table represents the outputs and the inputs for 3-bit squarer circuit where b2,b1,b0 are the inputs and P5 (MSB) ,P4,P3,P2,P1,PO (LSB) are the outputs Find the equation for PO Select one: O a. P4=b2b1' O b. P4=b2b1'+b2 O C. P4=b2b1'+b2b0 d. P4=b2b1'+b2b0'
Design a-full subtractor with two multiplexers (MUXS) S(xy.2) = E( ...) , C(x.y.2) = E( ...). Connect the variable z to the data inputs. Connect the variables x and y to the selection inputs.
Design a circuit that will multiply BCD ( Binary Coded Deciamal code) numbers which are between 0-9 with 10 (ten). Use an inverting output (4-10) Decoder. (Note: if input is 3 in BCD, output must be 3x10=30 in BCD)
Design a circuit to convert a 4-bit binary code to a 4-bit virgin reflective code (GRAY). Use a 4X16 decoder in the design.
Design and draw an 11-to-2^11 decoder with a) No predecoding. b) With predecoding. It is known that the first layer of predecoding uses 4 inputs nand gates.
An 8 x 1 multiplexer has inputs A , B , and C connected to the selection inputs S2 , S1 , andS0 , respectively. The data inputs I0 through I7 are as follows:(a) I1 I2 I7 0; I3 I5 1; I0 I4 D ; and I6 D ’.(b) I1 I2 0; I3 I7 1; I4 I5 D ; and I0 I6 D ’.Determine the Boolean function that the multiplexer implements.
Digital Logic Design4-bit Binary Adder / Subtractor please answer the whole sheet
Design the circuit F (A, B, C, D) = (0, 1, 2, 7, 8, 9, 14, 15) using 3 of 8 decoder
Given two 8-bit unsigned numbers, A and B:Using MSI components (comparators, multiplexers) design a circuit whose output X is as follows: X IF A <=B 2B IF A >B 2A