A bar of steel has the minimum properties Se = 276 MPa, Sy = 413 MPa, and Sut = 551 MPa. The bar is subjected to a steady torsional stress of 103 MPa and an alternating bending stress of 172 MPa. Find the factor of safety guarding against a static failure, and either the factor of safety guarding against a fatigue failure or the expected life of the part. For the fatigue analysis use: (a) Modified Goodman criterion. (b) Gerber criterion. (c) ASME-elliptic criterion.

A bar of steel has the minimum properties Se = 276 MPa, Sy = 413 MPa, and Sut = 551 MPa. The bar is subjected to a steady torsional stress of 103 MPa and an alternating bending stress of 172 MPa. Find the factor of safety guarding against a static failure, and either the factor of safety guarding against a fatigue failure or the expected life of the part. For the fatigue analysis use: (a) Modified Goodman criterion. (b) Gerber criterion. (c) ASME-elliptic criterion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel bar, both ends ball-jointed, is 0,6 m long and has a cross-section of 15mm x 5 mm. Use the Euler formula to estimate the maximum central deflection before the yield stress (assume this to approximate the proportional limitstress) of 300 MPa is reached in the material (E = 200 GPa).
Mechanical design
Consider the steel arm assembly in the figure below that supports load R. Using the Coulomb-Mohr failure theory and a factor of safety of n = 1.1, determine the maximum allowable value of R in kN. Let d = 50 mm, 0u = 210 MPa, Ou = 500 MPa.
You are using a 10 mm thick and 25 mm wide, steel plate with a central hole of 5 mm subjected to a tension load as shown in the figure (1). The load fluctuates between 5 and 25 kN. Determine factor of safety against yielding and against fatigue using modified Goodman. Assuming reliability of 98%, and the plate is made of cold-drawn AISI 1050. d P Thickness, t Figure (1). Steel plate subjected to tension-tension
A circular hollow steel tube (outer diameter 30 mm, inner diameter 25 mm) is subjected to a cyclic torsional loading which varies from +0.1 kNm to -0.05 kNm. If the steel has properties of shear stress fatigue limit Sf = 100 MPa, and noting that the mean shear stress to which the tube is subjected is non-zero, determine the ultimate shear strength required (out) using the Modified Goodman fatigue criterion.
Please help with all, thank you in advance! Will give thumbs up
The steel AISI 4142 (450HB) will be subjected in service to a stress amplitude of 450 MPa and a mean stress of 400 MPa. A service life of 10,000 cycles is desired. What are the safety factors in stress and in life?
Read and Solve carefully please Write clearly and Box the Final answer Express your answer to 3 Significant figures and include appropriate units. QUESTION : Recall that for spings the Zimmerli point on the modified Goodman diagram is located at (Ssm, Ssa) = (55, 35) ksi. Suppose that a particular spring wire has a shear ultimate strength of Ssu = 89 ksi. Determine the shear endurance limit of the spring wire. Give your answer in units of ksi,
shows a round bar subjected to a bending load F = 0.80 kN, and axial tension P = 7.2 kN, and a torsional load T = 40N.m. The round bar is made of steel with S, = Syc = 490 MPa. Compute the stress components and the magnitude of %3D principle stresses that act at A. Determine the factor of safety using Distortion Energy Theory 100mm F Ø20mm P T
Assume: Yield strength = 100ksi
Machine Element Design
Problem 2: (M6) A brittle material has the properties Sut=30 kpsi and Suc-90 kpsi. Using the brittle Coulomb- Mohr and modified-Mohr theories, determine the factor of safety for the following states of plane stress. Ox=215 kpsi, oy=10 kpsi, txy=215 kpsi