A bar of steel bar transmits a steady torsion of 30 kpsi while being subjected to an alternating bending stress of 45 kpsi. The material properties are given as Se 50 kpsi, Sy 72 kpsi, and Sut 85 kpsi. Find the factor of safety guarding against fatigue failure. For the fatigue analysis use: Modified Goodman criterion.

A bar of steel bar transmits a steady torsion of 30 kpsi while being subjected to an alternating bending stress of 45 kpsi. The material properties are given as Se 50 kpsi, Sy 72 kpsi, and Sut 85 kpsi. Find the factor of safety guarding against fatigue failure. For the fatigue analysis use: Modified Goodman criterion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical steel bar 8 mm in diameter is loaded 1000 cycles per day with a load of 15560 N. How long until fatigue failure takes place? Note: stress force/area 500 450 400 350 Steel Allby 300 250 200 150 Brass Alloy 100 50 1.00E-07 Cycles to Failure, N 1.00E+04 1.00E+05 1.00E-06 1.00E+08 100E+09 1.00E+10 , The bar should not fatigue. ) The bar will fail in one cycle. ) 100 days ) 1000 days Stress Amplitude, MPa
The beam is designed to carry a fluctuating stress from a load of 1,200-lb. The beam is made of Cold-Drawn AISI 1040 steel (wrought steel). Using the Goodman Method for Fatigue of Ductile materials, determine the design factor, N. 10 in 1200 lb 10 in 2-in dia
100 N R 19 PO A S 50 KN Z 0.9m Im W 0.2m Figure 1: Representation of the Lamp Post with Bracket 0.85m Note that: Height (h)=6 Thickness (t)=20 Calculate the ff: a. Consider that you want to evaluate a very short segment of length AL that runs along the middle of bar SW. What is the deformation along x, y and z in terms of AL? Take the case of linear-elastic behavior. G = 75 gigapascals E is 185 gigapascals Figure 2: Detailing of the Pin Support at W
The stepped and surface-ground steel bar in the figure is subjected to a bending moment varying between Mz=100 Nm and Mz=250 Nm and a torsional moment varying between Tx=80 Nm and Tx=320 Nm in opposite directions. The tensile strength of the rod material is Sut=800 MPa and it works under room conditions. For 50 percent reliability, check the fatigue safety of the rod.
The LPG tank with an inner diameter of 420 mm and a wall thickness of 2.2 mm in the figure operates under an internal pressure ranging from zero to 3.2 MPa. Also, an axially variable torsional moment of Tmax=10 kNm and Tmin=3 kNm is applied to the tank. The tank made of hot rolled steel sheet operates at ambient temperature. Accordingly, calculate the fatigue safety of the tank for 50% reliability? (yield strenght=460 Mpa,tensile strenght=520 Mpa) Note=Since there is no notch effect in the cylindrical part of the tank, take all kf as 1. For 50% reliability, take kc = Axial * Torsion = 0.51. Take the size factor kb = 0.85.
Q4 Beta =111 Please provide justified answer asap to get a upvote
A round bar of length /= 100 mm, diameter d 20 mm, is subjected to an axial force P- 500 N, a transverse force F5000 N, and a torque T-50 N.m. The material is steel with Sy 480 MPa. Using the distortion energy (Von Mises) yield criterion, calculate the safety factor at points A and B. 20 D. Select one: O a. NA = 7.897, Ng = 4.958 O b. NA = 0.624, Ng- 4.352 Oc. NA 4.768, Ng 2.346 O d. NA = 0.749, Ng =5.223
Parvinbhai
The cold-drawn AISI 1040 steel bar shown in the figure is subjected to an axial load fluctuating between 0kN and 28kN. Estimate the fatigue factor of safety based on achieving infinite life using modified Goodman criterion and the yielding factor of safety. If infinite life is not predicted, estimate the number of cycles to failure.
A Component shown in figure below machined from a plate of steel C45 having ultimate strength as 630 MPa, yield stress as 540 MPa and endurance strength 225 MPa. It is subjected to a completely revered axial load from -50 kN to +50 kN and the factor of safety is 2. Determine the plate thickness having width as 100 mm by using soderberg fatigue equation.
A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength of 240 MPa and endurance limit in reversed bending is 160 MPa. According to the Soderberg principle, the area of cross-section in mm2 of the bar for a factor of safety of 2 is
I need the answer as soon as possible