Please choose the correct answer with solutionTha k u 4GX02:55:03 RemainingMultiple ChoiceA ball is thrown vertically upwardwith an initial speed of 80 ft/sec from the base A of a 50-ftcliff. Neglect air resistance andthe small horizontal motion ofthe ball. Use g = 32.2 feet persecond squaredHow high from A will the ballreach?1 attachmentBr11058 ftO 74.18 ftO 105.24 ft=1:1150'8 of 103 4GX02:55:01 RemainingMultiple ChoiceA ball is thrown vertically upwardwith an initial speed of 80 ft/sec from the base A of a 50-ftcliff. Neglect air resistance andthe small horizontal motion ofthe ball. Use g = 32.2 feet persecond squaredAt what time will the ball land onpoint B?1 attachment.1:11Br116O 5.218 sO4.236 SO 6.218 s||||=50'9 of 103

Answered: Image /qna-images/answer/0a58d124-f8a5-44c8-9cac-71936fb9379b.jpg

A ball is thrown vertically upward with an initial speed of 80 ft/ sec from the base A of a 50-ft cliff. Neglect air resistance and the small horizontal motion of the ball. Use g = 32.2 feet per second squared At what time will the ball land on point B? 1 attachment B r 11 O 5.218 s O 4.236 s 6.218 S 50'

A ball is thrown vertically upward with an initial speed of 80 ft/ sec from the base A of a 50-ft cliff. Neglect air resistance and the small horizontal motion of the ball. Use g = 32.2 feet per second squared At what time will the ball land on point B? 1 attachment B r 11 O 5.218 s O 4.236 s 6.218 S 50'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1: 1. The figure shows two steel shafts connected by a steel pipe with interference. Modulus of elasticity = 210000MPa, Poisson's ratio = 0.3, and Coefficient of friction = 0.1. Fill the following table: L2 Interference H6/n5 dl 58 mm S2 d2 100 mm LI 70 mm L2 150 mm shaft diameter, d = mm Shaft inner diameter, di = mm Hole outer diameter, do = mm Interference length = mm Coef. Of friction = Modulus of elasticity Poisson's ratio Interference type Мах. Min. Interference micron Мра Pressure = Force = N Torque = Nmm Capacity of the assembly press Allowable transmitted torque Nmm - LP
Determine the z-coordinate of the centroid of the rectangular solid with the hemispherical hole. The center of the hemisphere is centered on the upper face of the solid, and z is measured upward from the lower face. 2.15 R Answer: Z = i R Touthook and Media 1.80 R 2.15 R R
I need a quick solution within 15 minutes With my best wishesT
Do not round off in between solutions and box your final answer. Correct answer should be 130
Steve Roger measured a line and found it out to be 950 m long using a 20 – m tape under a steady pull of 4 kg at a mean temperature of 25°C. The tape was held in the air and supported at both ends and at the center. Determine the correct length of the line if the tape used is of standard length at 22°C under a pull of 6 kg. Assume the cross-sectional area of tape to be 0.05 cm2, modulus of elasticity as 2.10 x 10^6 kg/cm^2, weighs 0.08 kg/m, and a Coefficient of Thermal Expansion to be 0.0000116/°C.
Fyi my student number is 202212051.The one with abcdefg W may be my number
Show Free Body Diagram Show complete solution anf clear hand writing
Sheet 2: Do the required for the following questions: O1: dy Find the particular solution of 5 dx dy - 2y 3e" given that when x 0, y= - dx and dx Ans.: y = 44
I need the answer as soon as possible
I need a quick solution within 15 minutes With my best wishesTon.
Question is in picture 1. Picture 2 contains the answer. Kindly check the answer before submitting the solution.
In (Figure 1), take b = 9 in. and h = 19 in. Figure h 6²-42 b 1 of 1 Locate the centroidy of the area. Express your answer to three significant figures and include the appropriate units. -- ÿ = 570 Submit HA Provide Feedback in STO Previous Answers Request Answer ? * Incorrect; Try Again; 5 attempts remaining