a) b) (A+B)(A + C) = c) A(B+C) d) A+ (B+C) A + AB (A+B) + C A + BC AB + AC = A + B

Q: Another name for comparator is O process O controller O error detector O actuator

A: Comparator: It has two analog input terminals and and one binary digital output . It is a device…

Q: Can you please help me design some instructions that ze ros the content of the accumulator register?

A: The given description is shown below.1Next step[1:0] 2_ 3Use_pc 4Load_mar 5arith 6invert 7pass…

Q: is the most important segment and it contains the actual assembly language instructions to be…

A: microprocessor works based on the assembly lenguage instruction provided to it.

Q: Give two examples each of electrical impedance cell counting machines and light scatter cell…

A: Give two examples each of electrical impedance cell counting machines and light scatter cell…

Q: clock cycles form one bus cycle. ROM can be classified into Dynamic ROM and Static ROM. Select one:…

A: 4 clock cycles are needed to form 1 bus cycle       RAM is classified into dynamic RAM and static…

Q: 22

A: To make a physical quantity observable by an instrument.... Is used ?

Q: The relation between the output and input of the sensor is O a. Non linear O b. inversely…

A: Given data:

Q: Approximately, what is the percent jitter for the following signal? 0.012 0.005 0.011 0.01 主

A: Jitter is a plot which is used to show the value distribution which are very consolidated. It gives…

Q: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

A: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

Q: The register circuit is: O A. A storage device O B. A data selector O C. A code generator O D. None…

A: In this question they are interested in the definition of the register .     Generally registers are…

Q: Problem Statement & Instructions: 1. State the resolution for each Digital Readout (DRO). 2. For…

A: RESOLUTION A measure of the sharpness and clarity of an image or picture is called resolution. It's…

Q: n of the following is r ding devices? . Digital Recorders . Ultra Violet Recor . Magnetic Tape Re .…

A:

Q: Series connection of switches would normally create O NOR logic gate O NAND logic gate O AND LOGIC…

A:

Q: We write the following code to configure a time delay of around 0.25 seconds. LDI R17, 0XDF L1: LDI…

A:

Q: In order to exchange the output polarity of the induced electromotive force in the self-excited…

A:

Q: The first element in any measuring system is the O variable conversion element signal processing…

A: Measurement of any quantity is the comparison of the measured value with a pre defined standard.…

Q: What is not a characteristic of the RS-485 electrical standard? It allows either single ended or…

A: What is not a characteristic of the RS-485 electrical standard

Q: Compare between DS & DI registers?

A: DI = DESTINATION INDEX REGISTER   DS = DATA SEGMENT REGISTER

Q: Draw and label the block diagram of the instrumentation calibration chain.

A: Instrument calibration- Calibrating an instrument is to ensure that the instrument is working…

Q: multiplexer contains. multiplexer contains.... select lines 4-1 4 O 20 8 O select lines 16-1 4 O 8 5…

A: In this question we need to choose a correct option

Q: Change hexa decimal number(45B1) to the decimal number

A: The representation of the number for the hexa-decimal system is given as:

Q: QI Compare between CAS and CCS signaling techniques

A: In communication system a call has to be initiated ,maintained and disconnected . This process is…

Q: It is also called On-Off Keying a. QAM b. ASK c. FSK d. BPSK

A: Amplitude-shift keying (ASK) is also called as On-Off keying. Reason for ASK called as on off key…

Q: When the MPU does a write it (receives/sends) data.

A: MPU stands for microprocessing unit it consists of a microprocessor, memory, and input-output…

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: Choose how many and determine the type of output (digital or analog) it gives and how to interface…

A: 16 channels on the ESP32 can be utilized to generate PWM signals, allowing for a maximum of 16…

Q: 5) In an astable multivibrator when the capacitor is capacitor is using a 555 timer, the and the…

A: For the above given question we need to define the behaviour of the capacitor.

Q: Do Y. So EN Parity generator Demultiplexer Decodor 身

A:

Q: What is the accuracy of bellow sensor? O a. ± 1% O b. ± 0.001% O c. ± 0.1% O d. ± 0.01%

A: At high differential pressures the accuracy is around 1.5% of the measuring range.  and At lower…

Q: Unfortunately, as soon as the button is released, the LED turns off and will not come back on when…

A: According to the question, the pseudocode program is given as,Declare Pint as an inputWHILE Pint is…

Q: QUESTION 44 The 8259 is a O Low priority interrupt O Tristate buffer Programmable Peripheral…

A: Intel 8259 is a very important device and very commonly with 8085/8086 systems.

Q: The serial data input waveform (Data in) and data select input (So and S₁) are shown below.…

A:

Q: Question No. 1: Summarize the following (two to three lines) a) Difference between precision and…

A: we need to summarize the following:a) Difference between precision and accuracy.b) Difference…

Q: DUT AN O ipleser CLK Flip-flop Tristate output butler clock SP Observe the OLMC and programmed…

A:

Q: The information signal is always an analog signal. an analog signal in case of an analog carrier…

A: Given : Information signal is  a) always an analog signal  b) an analog signal in case of an analog…

Q: Flash type ADC gives highest conversion rate. Select one: True False

A: Flash type ADC

Q: Represent the fallowing cet Diogram into blockDiagram R

A: Basic electrical circuit problem.. Below is the solution..

Q: 2. TIMING DIAGRAM Positive Level-clocked D Latch CLK D

A:

Q: In an estable multivibrator using a 555 timer, the out put is and the high or logic (1) when the the…

A: Astable multivibrator using 555 timer : An Astable multivibrator using 555 timer is act like a…

Q: Determine output logic clear but clear buble are inversions the black dots are nodes

A: Given here logic circuit and asked to find the output

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).