a) A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated "if one or more than one parameter exceeds the safe value, a protective measure is needed to be done". As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action.

a) A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated "if one or more than one parameter exceeds the safe value, a protective measure is needed to be done". As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
c) List FOUR (4) main inputs to the Motor Driven Power Steering Control Module (MDPSCM) and explain the used of the input listed above. d) Explain TWO (2) safety precaution.that electrical power steering E.C.U will take action if:- a. If a sensor or other component in the EPS system fails b. the electrical power steering motor overheating
The switch is said to be __________ when one side of it is connected to the ground and pressing it will cause the input to the microcontroller to be low. a. Pull-down resistor b. Active-Low c. All of the mentioned d. Push button
Write in your own words
What does the Arduino instruction pinmode do in the Traffic Light program?
Q1. Multiple Choice: 1. During forward blocking state, the SCR has (a) low current, medium voltage. (b) low current, large voltage. (c) medium current, large voltage. (d) large current, low voltage. 2. In a SCRS (a) both Latching current and holding current are associated with turn-off process. (b) latching current is associated with turn-off process and holding current with turn on process. (c) holding current is associated with turn-off process and Latching current with turn-on process. (d) both Latching current and holding current are associated with turn on process. 3. In a thyristor, the magnitude of anode current will (e) increase if gate current is increased. (b) increase if gate current is decreased. (c) decrease if gate current is decreased. (d) not change with any variation in gate current. 4. Turn on time of an SCR can be reduced by using a (f) rectangular pulse of high amplitude and narrow width. (g) rectangular pulse of low amplitude and wide width. (h) triangular pulse.…
ך.:lP 4G Ooredoo llı. Expert Q&A Done Topic; Plc based automatic intelligent car parking system. Q1; Concepts, principles and theories regarding the special components and Tools Need explain the each component you are using in the project PLC software PLC sensor IR sensor LDR sensor Security camera - Solar panel - Batteries . Push button switch
Please answer this question fast.
In the voltage-controlled square/triangular waveform generator circuit we covered, is the transistor switch able to pull its drain towards the smallest possible voltage when it is ON? Which regimes of operation would you expect the transistor switch to remain for longer time intervals during the operation of the circuit, and why? Explain.
Question: Describe the functionality of the following buttons and LEDs on the front panel while making use of these buttons to power your circuit. Describe buttons and LEDs below. 1. CURRENT (A) = ? 2. VOLTS =? 3. OUT = ? 4. C.C = ? 5. C.V = ? 6. DATA ENTRY = ? 7. VOLTS SET = ? 8. CURRENT SET = ? 9. OUTPUT ON/OFF = ? 10.SHIFT ON/OFF = ? 11. POWER = ? 12.OUTPUT 1, OUTPUT2, OUTPUT 3 =?
Question 14
Don't give copied solution, need urgently