a) A multiplexer (MUX} is a combinational circuit that selects binary information from one of many input lines and directs it to a single output line. Design a 8:1 multiplexer using the function: F(A,B,C,D)=Σ (0,2,4,5,7,10,12,14,15), Major Topic Multiplexers b) Implement the Boolean function below using a 4:1 multiplexer F(A, B,C)=Em (0, 2, 5, 6) Major Topic Multiplexers Text Blooms Designation AP Major Topic Demultiplexers Blooms Designation AN c) A Demultiplexer (Demux) has one input, 2n possible outputs and n control or selection lines. It is also called a data distributor. Design 8:1 Demultiplexer for a mobile telecom company Blooms Designation AP

a) A multiplexer (MUX} is a combinational circuit that selects binary information from one of many input lines and directs it to a single output line. Design a 8:1 multiplexer using the function: F(A,B,C,D)=Σ (0,2,4,5,7,10,12,14,15), Major Topic Multiplexers b) Implement the Boolean function below using a 4:1 multiplexer F(A, B,C)=Em (0, 2, 5, 6) Major Topic Multiplexers Text Blooms Designation AP Major Topic Demultiplexers Blooms Designation AN c) A Demultiplexer (Demux) has one input, 2n possible outputs and n control or selection lines. It is also called a data distributor. Design 8:1 Demultiplexer for a mobile telecom company Blooms Designation AP

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Question 5: F(a,b,c,d)=I(0,1,3,6,10,11,14) Implement the above boolean function using a. 4:1 MUX(s) and 2:1 MUX(s) [both in the same circuit]. b. 8:1 MUX You can also use minimal number of BASIC gate(s) with the above-mentioned decoders.
design a circuit to implement a dynamicdisplay of two lights. and use several 2:1Mux, only one seven-segment display decoder andonly one 2:4 decoder
Implement the following function with a8-to-1-line Multiplexer with threeselection lines? Draw the truth table and the corresponding block diagram for the MUX?F(A, B, C, D) = Σm ( 1, 3, 4, 11, 12, 13,14,15 )
i need the answer quickly
Consider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c,…
Answer all
Digital 6design
Implement the diagram in part b and verify its function experimentally by constructing a truth table from the test data.
Design a-full subtractor with two multiplexers (MUXS) S(xy.2) = E( ...) , C(x.y.2) = E( ...). Connect the variable z to the data inputs. Connect the variables x and y to the selection inputs.
Design a circuit using a Multiplexer, (((USING A MULTIPLEXER NOT A DECODER))) that has two inputs X, and S, where X represents an 8-bit BCD number,S is a sign bit. The circuit has one output Y, which is the Binary representation of thesigned-magnitude BCD number. A negative output is represented in the Binary 2’scomplement form.
3. Implement a full – adder circuit using 4 to 1 multiplexers.