(a) A linear time invariant (LTI) system relating an input to the output of a system is defined by the linear difference equation below. y[n] = 0.9x[n-1] +0.3x[n] +0.24x[n-1] (i) Write an expression for the convolution sum relating the output response to the input and find the impulse response h[n] of the system. (ii) If the input of the system is x[n] = {3, 5, 2, 7}, write an expression for the input sequence in terms of the unit impulse function. Find the output response y[n] of the %3D system for the given input x[n] = {3, 5, 2, 7}

(a) A linear time invariant (LTI) system relating an input to the output of a system is defined by the linear difference equation below. y[n] = 0.9x[n-1] +0.3x[n] +0.24x[n-1] (i) Write an expression for the convolution sum relating the output response to the input and find the impulse response h[n] of the system. (ii) If the input of the system is x[n] = {3, 5, 2, 7}, write an expression for the input sequence in terms of the unit impulse function. Find the output response y[n] of the %3D system for the given input x[n] = {3, 5, 2, 7}

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The signals x(n) and y(n) shown in figure are the input and corresponding output ofan LTI system.- Find the response of the system to the sequence x2(n) shown in the figure.- Find the impulse response of the LTI system.
Q3)a)For a LTI system the input output relation is given by y(r e "-1)x(7 – 2)dr. Find the impulse response of the system b) For the system in (a) find and draw the output if x(t) is as below
Q2)a)Given x(t) and the impulse h1(t) as below find and draw y(t) h1(t X(t 1 1 1 -1 b)for the same system in a if the impulse response of the system is given as h(t) = > h1(t – 2m) m=-00 For the same input find and draw y(t) c)find the total energy and power of the following signal X(t) 1 -5 -4 4
The causal, LTI system described by y(n) – 0. 5y(n –1) = Bx(n- 1) - x(n- 2). The B such that the system has a finite impulse response is Answer
Signalse and system
Note: I just need to know the correct answer. Thank you from now. This question's answer is very important for me.
Length of the linear convolution output y[n] is 400 and length of the impulse response h[n] is 40. Then the length of the input sequence x[n] assuming that the length of linear convolution output is reduced by 50% is.
Signal and systems. I would appreciate clear step by step to understand this problem. Thanks
Find the impulse response of the systems below. Use the impulse response to find the output for unit step input. Comment on the ROC of the impulse response, and stability (a) y(n) – 10y(n-1) = x(n) + x(n-1) (b) y(n) – 3y(n-1) + 2y(n-2) = x(n)
Signal and system
The unit impulse response of a second order system is (2) 6 the natural frequency and damping ratio of the system are respectively? -0.8t e sin (0.6t). Then
make sure to write the difference equation