A- A delta modulator system is designed to operate at fi ve times the Nyquist of input rate for an analog information signal band-limited to 3 kHz. The quantizing step-size is 40 mV. Determine the maximum allowable amplitude analog signal for which the delta modulator does not experience slope- overload distortion. Compute the Signal-to-quantization noise ratio (So/Nq) for PCM and DM system for the speech signal which has a bandwidth of 3200 Hz. Assume n=2 in a code-word. Comment on the result. smitted

A- A delta modulator system is designed to operate at fi ve times the Nyquist of input rate for an analog information signal band-limited to 3 kHz. The quantizing step-size is 40 mV. Determine the maximum allowable amplitude analog signal for which the delta modulator does not experience slope- overload distortion. Compute the Signal-to-quantization noise ratio (So/Nq) for PCM and DM system for the speech signal which has a bandwidth of 3200 Hz. Assume n=2 in a code-word. Comment on the result. smitted

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. The information in an analog voltage waveform is to be transmitted over a PCM system with a F 0.2% accuracy (full scale). The analog waveform has a bandwidth of 200 Hz, and an amplitude range of -5 to +5 V. determine the following: - The minimum sampling rate needed. - The number of bits needed in each PCM word. - The minimum bit rate in the PCM signal. - The minimum channel bandwidth for transmission of this PCM signal.
2. Draw a labelled block diagram of a unity-gain multirate signal processing system that converts an input signal with sampling frequency 10 kHz to an output signal with sampling frequency 10.5 kHz.
(Subject name is "Signal and system") Determine the Nyquist sampling frequency of square wave pulse with width of 2πs.
AF ADM system is designed to operate at 3 times the Nyquist rate for a signal with a 3 kHz bandwidth. The quantizing step size is 250 mV. *** (i) Determine the maximum amplitude of a 1-kHz input siinusoid for which the delta modulator does not show slope overload. (ii) Determine the posfiltered output part (i) signal-to-quantizing-noise ratio for the signal of
B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) The waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 12
Does a PCM signal have a smaller bandwidth? Why or Why not?
2/ Information in an analog waveform, whose maximum frequency is 10 kHz, will be transmitted using a minimum sampling rate and a 32-PAM system. transmitted using a minimum sampling frequency and a 32-PAM system. The quantization distortion shall not exceed 0.01% of the The quantization distortion must not exceed 0.01% of the peak-to-peak value of the analog signal. a/ What is the minimum PCM word size to be used in the system? b/ What is the baud rate?
What is the main disadvantage of linear delta modulation? What is the solution for this problem? this question from digital communication course.
Q2: A PAM signal f(t) = 2cos n 4t is sampled at rate of 16 Hz using 8 – levels quantization. Indicate the quantization intervals and corresponding digital words. * Note (that the question relates to communication materials)
What is a minimum number of sampling frequency required to have distortion free reconstruction of a digital signal from its samples?
7. Why does PTM require a higher sampling frequency than PAM? a. The amplitude of PTM signals is constant. b. There are more sidebands in the first replica of a PTM c. Signal than in a PAM signal. d. A sample/hold circuit requires a higher sampling frequency. e. There are fewer sidebands in the first replica of a PTM signal f. Than in a PAM signal.
3 ) Time taken for the output signal rise to 95% from 10% is called rise time Select one: True False